background image

080205-8 

TC36.NG01      7

ITEM ..... DESCRIPTION ..................................... PART NO.

1............ LOG GRATE ....................................... TC36.9181
2............ BURNER TRAY .......................... TC36.9787WLD
3............ ORIFICE, NG ........................................... 5022.13
.............. ORIFICE, LP ............................................ 5021.34
4............ MANIFOLD .......................................... TC36.9788
5............ PILOT SHIELD ......................................... 9780.01
6............ BURNER TRAY SUPPORT SHIELD ....... 9789.01
7............ BURNER TRAY SHIELD GASKET ............ 9789.5

1

2

6

7

5

3

4

REPLACEMENT PARTS

....... DESCRIPTION ........................................... PART NO.

....... LOG SET, COMPLETE ............................... 5098.7461
....... REAR, #1 

(shown in fig.#11)

 ........................ 5098.741

....... LEFT, #2 

(shown in fig.#11)

 ......................... 5098.742

....... RIGHT, #3 

(shown in fig.#11)

 ....................... 5098.743

....... MIDDLE, #4 

(shown in fig.#11)

 ..................... 5098.744

....... BOTTOM LEFT, #5 

(shown in fig.#11)

 ......... 5098.745

....... BOTTOM CENTRE, #6 

(shown in fig.#11)

 ... 5098.746

Fig. # 14

IDENTIFICATION 
NUMBER

Summary of Contents for TC36.NG01









Reviews: