background image

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VISIT 

WWW.TOWNSTEEL.COM  FOR 

17901 RAILROAD STREET 

CITY OF INDUSTRY, CA 91748 

TOLL FREE: 877-858-0888 

 

 

 

 

 

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment 

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause 

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. 

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment 

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/ TV technician for help.

RF Exposure warning  

This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter 

must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in 

conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and

 transmitter operating conditions for satisfying RF exposure compliance. 

Summary of Contents for e-Elite 3000

















Reviews: