2
3
1. Outside Escutcheon Assembly (1)
2a. Inside Spindle (1)
2b. Outside Spindle (1)
3. Mortise Lock Case (1)
4. Lock Case Screws (2)
5. Face Plate (1)
6. Face Plate Screws (2)
7. Inside Escutcheon
Trim/Lever Assembly (1)
(Thumbturn Optional)
8. Assembly Mounting Screws (4)
9. Mortise Cylinder (1)
(Optional)
10. Wave Spring (1)
(Optional)
11. Cylinder Collar (1)
(Optional)
12. Dustbox (1)
13. Strike (1)
14. Strike Screws (2)
Strike and Dustbox
for Door Jamb.
1. Outside Lever Assembly (1)
2a. Inside Spindle (1)
2b. Outside Spindle (1)
3. Mortise Lock Case (1)
4. Lock Case Screws (2)
5. Face Plate (1)
6. Face Plate Screws (2)
7. Thumb Turn Assembly (1)
(Optional)
8. Thumb Turn Screw (2)
(Optional
)
9. Inside Lever Assembly (1)
10. Assembly Mounting Screws (2)
11. Inside Rose (1)
12. Mortise Cylinder (1)
(Optional)
13. Wave Spring (1)
(Optional)
14. Cylinder Collar (1)
(Optional)
15. Dustbox (1)
16. Strike (1)
17. Strike Screws (2)
Strike and Dustbox
for Door Jamb.
Step 1: Prepare door per template (supplied).
Step 2: Insert lockcase 3 into mortise cut-out (faceplate removed)
and fasten to door with 2 screws 4 .
Step 3: Insert inside 2a and outside 2b spindles into the lockcase hubs and tighten screw.
Step 4: Install outside escutcheon trim 1 onto spindle 2b & 4 post thru holes on the
door.
Step 5: With the deadbolt projected, install the inside escutcheon Trim/Lever assembly
(Thumbturn in horizontal position) 7 onto spindle 2a & secure inside 7 /outside trim
assemblies with 4 screws 8 temporarily
Step 6:
Optional: Install cylinder 9 , wave spring 10 and cylinder collar 11 .
Adjust accordingly, tighten set screw and check lock (use key) for function.
Step 7: Install faceplate 5 with two screws 6 .
Step 8: Tighten screws 8 and check lock for fit and function.
Step 9: Install dustbox 12 and strike 13 to jamb and fasten with screws 14 .
Step 1: Prepare door per template (supplied).
Step 2: Insert lockcase 3 into mortise cut-out (faceplate removed)
and fasten to door with screws 4 .
Step 3: Insert inside 2a and outside 2b spindles into the lockcase hub and tighten screw.
Step 4: Install outside lever assembly 1 onto spindle 2b with the screw posts
thru holes in lockcase.
Step 5: Install inside mounting plate/lever assembly 9 onto spindle 2a and secure
inside 9 /outside 1 assemblies with two 10 screws temporarily.
Step 6:
Optional: Install cylinder 12 , wave spring 13 and cylinder collar 14 .
Adjust accordingly, tighten set screw and check lock (use key) for function.
Step 7: Install faceplate 5 with two screws 6 .
Step 8: Tighten screws 10 and check lock for fit and function.
Step 9: Slide inside rose 11 onto inside lever assembly 9 . Align indented dot over bottom
notch and press to secure.
Step 10: Install dustbox 15 and strike 16 to jamb and fasten with screws 17 .
Step 11: Install thumbturn assembly (if required).
