3. INSTALL NO.1 OIL PAN
(a) Remove any old packing (FIPG) material and be care–
f uI not to drop any oil on the contact surfaces of the
oil pan, oil pump and cylinder block.
•
Using a razor blade and gasket scraper, remove
all the old packing (FIPG) material from the
gasket surfaces and sealing grooves.
•
Thoroughly clean all components to remove all
the loose material.
•
Using a non–residue solvent, clean both sealing
surfaces.
(b) Apply seal packing to the oil pan as shown in the
illustration.
Seal packing:
Part No. 08826–00080 or equivalent
Region “X” is at the outer side of the bolt hole.
Region “Y” Is at the inner side of the bolt hole.
•
Install a nozzle that has been cut to a 4–5 mm
(0.16–0.20 in.) opening.
HINT: Avoid applying an excessive amount to the
surface.
•
Parts must be assembled within 3 minutes of
application. Otherwise the material must be re–
moved and reapplied.
•
Immediately remove nozzle from the tube and
reinstall cap.
(e) Install the oil pump with the 9 bolts.
Torque:
8 N–m (80 kgf–cm, 69 in.–lbf) for 10 mm head bolt
19.5 N–m (200 kgf–cm, 14 ft–lbf) for 12 mm head bolt
2. INSTALL OIL PAN BAFFLE PLATE
Install the baffle plate with the 6 bolts.
Torque: 8 N–m (80 kgf–cm, 69 in.–Ibf)
–
1MZ–FE ENGINE
LUBRICATION SYSTEM
EG2–387
Summary of Contents for 1 MZ-FE
