SERVICE SPECIFICATIONS - Engine Mechanical
A-3
Specification (Cont'd)
Engine tune-up
(cont'd)
Valve clearance Intake
Exhaust
New valve adjusting shim thickness
Injection timing
Plunger stroke 1 PZ
1HZ
1HD-T
Idle speed 1 PZ
1HZ (M/T)
1 HZ (A/T)
1HD-T(M/T)
1HD-T (A/T)
Maximum speed 1 PZ and 1 HZ
1HD-T
A/C idle-up setting speed
Injection order 1 PZ
1 HZ and 1HD-T
0.1 5 - 0.25 mm 0.006 - 0.010 in.
0.35 - 0.45 mm 0.014 - 0.018 in.
2.35 mm 0.0925 in.
2.40 mm 0.0945 in.
2.45 mm 0.0965 in.
2.50 mm 0.0984 in.
2.55 mm 0.1004 in.
2.60 mm 0.1024 in.
2.65 mm 0.1043 in.
2.70 mm 0.1063 in.
2.75 mm 0.1083 in.
2.80 mm 0.1102 in.
2.85 mm 0.1122 in.
2.90 mm 0.1142 in.
2.95 mm 0.1161 in.
3.00 mm 0.1181 in.
3.05 mm 0.1201 in.
3.10 mm 0.1220 in.
3.15 mm 0.1240 in.
3.20 mm 0.1260 in.
3.25 mm 0.1280 in.
3.30 mm 0.1299 in.
0.82 - 0.88 mm 0.0323 - 0.0346 in.
1.03-1.09 mm 0.0406-0.0429 in.
1.29-1.35 mm 0.0508-0.0531 in.
650 rpm
650 rpm
710 rpm
650 rpm
800 rpm
4,600 rpm
4,400 rpm
950 rpm
1 - 2 - 4 - 5 - 3
1 _ 4 _ 2 - 6 - 3 - 5
Compression
pressure
Engine revolution at 250 rpm
1PZand1HZ STD
Limit
1HD-T STD
Limit
Difference of pressure between each cylinder
37.0 kg/cm
2
(526 psi, 3,628 kPa) or more
27.0 kg/cm
2
(384 psi, 2,648 kPa)
35.0 kg/cm
2
(498 psi, 3,432 kPa) or more
25.0 kg/cm
2
(356 psi, 2,452 kPa)
5.0 kg/cm
2
(71 psi, 490 kPa) or less
72.7 mm 2.862 in.
23 - 28 kg (50.7 - 61.7 Ib, 225 - 275 N)
Free length
Installed load at 90.1 mm (3.547 in.)
Idler pulley
tension spring
Timing gear
Idler gear inside diameter
Idler gear shaft diameter
Idler gear oil clearance STD
Limit
Gear backlash STD
Limit
Idler gear thrust clearance STD
Limit
45.000-45.025 mm 1.7717 - 1.7726 in.
44.950 - 44.975 mm 1.7679 - 1.7707 in.
0.025 - 0.075 mm 0.0010 - 0.0030 in.
0.20 mm 0.0079 in.
0.05 - 0.1 5 mm 0.0020 - 0.0059 in.
0.30 mm 0.0118 in.
0.05 - 0.1 5 mm 0.0020 - 0.059 in.
0.30 mm 0.0118 in.
Summary of Contents for 1HD-T
