Toyota Orderpicker Model
15
Service Manual
Section
8.
W i r e Guidance
Set-Up Procedure
Set-Up Procedure
6. From the main menu, type
s
for Set
Configurable Items a t the prompt. Make
sure the settings are correct for the
N
OTE
:
If you are setting u p a truck with
guidance application. Change settings if
factory-installed wire guidance, skip to
necessary.
4.
N
OTE
:
To change these settings:
1. Install the wire guidance kit components.
See "Install Kit Components" on page 8-3.
Use the u p and down arrows to select
2.
If necessarv, flash the latest version of
the options.
software
See "Flash
Use the left arrow to decrease values,
Memory Program" on page 10-6.
and the right arrow to increase values.
3.
Turn on the wire guidance option in
7.
After changing the truck configuration:
See "Enable Wire Guidance in
Truck restarts automatically
FlashWare" on page 8-9.
Horn beeps when self-diagnostics is
4.
Perform the Guidance Parameter Setup to
finished
set the distance from wire and heading
angle
See "Guidance
Parameter Setup" on page 8-9.
Screen returns to the main menu
8. Type
x
to exit FlashWare.
5.
Learn the guide wire frequency. See "Learn
Guide Wire Frequency" on page 8-
Guidance
6. Learn the guide wire offsets. See "Learn
1. Connect the FlashWare program to the
Wire Guidance Offsets" on page 8- 10.
truck.
7.
Perform the Guidance Check to make sure
the truck can steer on the wire properly.
turned on in FlashWare. See "Enable Wire
See "Guidance
on page 8- 1 1.
Guidance in FlashWare" on page 8-9.
Enable Wire Guidance in
FlashWare
3.
At the prompt on the Main Menu, type
s
for Setup Configuration Items and press
Enter key.
N
OTE
:
For complete instructions on FlashWare,
4.
Set the following parameters in the Truck
See "Software Configuration" on
Configure Menu.
page 10-1.
1. Make sure the latest version of FlashWare
is installed in the truck. If not, flash load
the latest version. See "Flash Memory
Program" on page 10-6.
2.
From the main menu, type
o
for Options a t
the prompt.
3.
From the options menu, use your arrow
N
OTE
:
If wire guidance is turned off in
keys to move to the Wire Guidance prompt
the Truck Configure Menu
and press the
enter
key.
will display the lift cutout threshold
4. In the box that appears on the left, type in
only.
the 4-digit authorization code you
5.
Type
x
to save these parameters and exit
obtained from the Toyota Parts
this menu.
Distribution Center.
Distance From Wire Slow
Distance From Wire Stop
Heading Angle Slow
Heading Angle Stop
5.
Type
y
a t the Wire Guidance prompt, and
follow the instructions a t the bottom of the
screen.
1.6
3.0
1.6
3.0
00700-CL222-05, 1 5
March
2005
Summary of Contents for 7BPUE15
