9
ERROR CODE
E-0
E-2
E-6
E-8
E-12
E-13
E-22
E-23
-- : --
Hi
Lo
INFORMATION
Power interrupted.
Ignition safety feature is activated.
Extinguished during operation.
Blower motor malfunction.
Overheating safety feature is activated.
Burner thermistor malfunction
Excess fuel in the burner
Ignition failure three times
Primary flame (Flame sensor) is malfunction and / or dirty.
Timer is not setting.
Room temperature is higher than 35˚C.
Position of room temperature sensor is not correct.
Room temperature is lower than -10˚C.
Room thermistor malfunction or disconnected.
WHAT TO DO
Re-ignite the heater
Contact your dealer
Contact your dealer
Contact your dealer
Clean the air filter and remove dust.
Contact your dealer
Contact your dealer
Contact your dealer
Contact your dealer.
Set the timer.
Check the position of room temperature
sensor.
Check the position of room temperature
sensor.
SECTION E:
ERROR MESSAGE
☞
☞
☞
☞
Step 4: Look for the source of the overheating.
Overheating is usually caused by objects that
obstruct the free flow of air. Check that the
circulation ventilator or exhaust pipes are not
blocked. Check that there are no objects
blocking the outlet system.
Step 5: Remove the front panel.
Step 6: Clean the inside of the heater.
Before starting to clean the heater, ensure
that the interior is cool enough to touch.
Wipe alldust off the outside of the housing
with a clean,non-fluffy, damp cloth or another
suitable cleaning aid. Do not forget to clean
the out side of the heat chamber and the heat
exchanger.
Step 7: Re-attach the front panel.
Step 8: Insert the heater plug into the socket.
Step 9: Switch the heater ON.
Step 10: Re-program the heater (clock and timer).
If the heater overheats after the completion of
a recovery procedure, contact your dealer
and do not switch the heater on until the
problem has been resolved.
10. Cleaning the filter (monthly)
Switch off the heater and let it cool down, before you
start any maintenance work. Also disconnect the plug
from the mains.
Your needs hardly any maintenance. It is, however,
important that you clean the louvers, grilles and
circulation fancover on the back of the heater weekly.
Periodically checkthe flue pipe connection for leakage or
separation.
We recommend that you remove dust and stains in time
with a damp cloth, because otherwise these may cause
stains that are hard to remove.
Do not remove any heater components
yourself. Always contact your dealer for
repairs. Whenthe power cord is damaged, it
may only bereplaced by an authorized fitter.
Use a new cordof the type H05 VV-F.
11. Before consulting an expert
The following situations do not indicate defects.
While switching the heater on or off.
White smoke can be seen when the heater is switched
on for the first time.
Machine oil or dust on the burner chamber or heat
exchanger is burning.
The flames flicker for several minutes after the heater
has been ignited.
The ignition rod continues to function when the heater is
cold, even several minutes after ignition. This may cause
the flames to be a little larger.
The heater makes intermittent creaking sounds when
warming up or cooling down.
Expansion and shrinkage of metal parts may cause a
slight creaking sound.
Circulation of air in the room does not start immediately
when the heater is lit.
To prevent unpleasant cold draughts, the ventilator only
switches on when the heater has become warm.
A loud clicking sound can be heard during the first use
or when the fuel runs out.
There is air in the fuel pump. This should be gone within
approximately 1 minute.
Note: The fuel pump may make a slight
ticking sound during normal operation. This
does not indicate a problem.
While the heater is in operation
A part of the burner pot and/or heat exchanger becomes
red in color during operation. This is normal and does
not indicate a problem.
