background image

FCC STATEMENT 

This equipment has been tested and found to comply with the 

limits for a Class A digital device, pursuant to part 15 of the 

FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference when the equipment is 

operated in a commercial environment. This equipment 

generates, uses, and can radiate radio frequency energy and, 

if not installed and used in accordance with the instruction 

manual, may cause harmful interference to radio 

communications. Operation of this equipment in a residential 

area is likely to cause harmful interference in which case the 

user will be required to correct the interference at his own 

expense. 

This device complies with part 15 of the FCC Rules. Operation 

is subject to the following two conditions: 
1)

 

This device may not cause harmful interference. 

2)

 

This device must accept any interference received, 

including interference that may cause undesired 

operation. 

Any changes or modifications not expressly approved by the 

party responsible for compliance could void the user’s 

authority to operate the equipment. 

CE Mark Warning 

 

This is a class A product. In a domestic environment, this 

 

Summary of Contents for PSM150-AC

















Reviews: