background image

10

SUBITO

Bring the seat directly into line with the suspension

Fig. 10 - 

4.5.  Moving the seat

Lower the seat to the ground and give sufficient

1. 

slack wire rope to the suspension wire rope.

Place the PORTAFIX™ suspension beam or the

2.

OMEGA parapet clamp in its new position.

Refer to the user manual for the 
suspension.

Bring the seat directly into line with the suspension

3.

(Fig. 10).

Retension the suspension wire rope by manoeu-

4.

vring the SCAFOR

TM

 hoist in UPWARDS direction.

Lift the seat support so that the seat is about 60 cm

5.

from the ground.

Carefully reel up the spare length of wire rope onto

6.

its reeler.

4.6.  Removing the wire ropes

This operation requires two operators, one near the 
seat and the second on the roof.

The operator working at a height 

must wear a safety harness and 
be attached to a sufficiently strong 

anchor point.

Risk of injury!

 

Wear safety gloves !

Lower the seat to the ground and give a sufficient

1. 

amount of slack to the wire rope.

Remove the clamp (7).

2.

Remove the lifting wire rope from the SCAFOR™

3.

hoist, operating it in the DOWN direction (see
chapter 4.4.).

Securely fasten one end of the cord (A) to the hook

4.

of the safety wire rope. Then, unscrew the nut (Fig.
7) on the lower safety hook (11).

Firmly hold the safety wire rope at the sleeve and

5.

remove the safety hook (11) from the carrier stirrup.

Using the cord, and

6.

 without releasing it

,

accompany the safety wire rope to its initial
position, allowing it to wind itself in the casing of
the BLOCFOR™ fall arrest device.

Bring the cantilevered section of the suspension

7. 

into the building.

The operator on the roof must unhook the fall

8.

arrest device BLOCFOR

TM 

and place it on the roof.

He must then recover the rope and lifting wire rope
connection, unhookthe wire rope and lower it to the
ground using the same rope.

Never let the wire rope fall under its 

own force of gravity.

4.7. 

Storage of fall arrest device 

BLOCFOR™

After unhooking the fall arrest device BLOCFOR

TM  

from 

the suspension anchor point, store the equipment in 
a dry place and away from adverse weather condi-
tions (humidity). The wire rope must be in its box, fully 
wound and clean.

Danger

Suspension

Warning

- MC1452-SUBITO_6FR-EN-D-IT-ES-NL  0

7

/201

8

Summary of Contents for subito















Reviews: