background image

 

     

  7 

If you find it necessary to use an extension cord with your compressor, make sure the cord is sufficiently rated for the 

motor power. The extension cord must also contain an earthing wire. Never operate the compressor with a coiled 

extension cable. Always repair or replace extension cords when they become worn or damaged. 

 

Only  trained  and  authorized  personnel  are  allowed  to  operate  the  compressor

.  Prior  to  any  operations,  the 

manual shall be carefully read and its contents shall be comprehensively understood.   

Never allow 

the unit to start in an unsafe condition; if problems occur to the unit, do not attempt to restart the unit 

until  the  fault  has  been  corrected.  The  power  supply  shall  be  shut  off  and  significant  indication  signs  shall  be 

positioned to alert other personnel not to attempt to restart the unit. 

Be aware that compressed air is  hazardous. Only once all  the compressed air is  totally  discharged in the 

whole compressor system may maintenance and service be performed on the unit.

 

 

Routine daily service and maintenance schedules are to be adhered to. The unit shall be carefully inspected every 

day  to  check  for  conditions  such  as  leakage,  loose,  damaged  and  poorly  adjusted  parts,  missing  parts  or 

components. If any such items are discovered refrain from starting the unit and contact your dealer.   

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for MCFRC227






















Reviews: