background image

Assembled dimensions (approximate): 6" long, 57" (on full) or 42" (on twin) wide, 86" high.

Model MAST-3 Bed Frame Accessory

Revised 10/27/2016

Page 

2 of 10

General Specifications

Use and Warnings

Your child’s safety is our top priority. Please observe the following safety warnings to ensure the safe 
use of this product:

 STRANGULATION HAZARD - Never attach or hang items to any part of this product that are not

designed for use with the product; for example, but not limited to, hooks, belts and jump ropes. 

 Do not stand, sit, hang, swing, or lean on any part of this product.

 Do not allow jumping or horseplay around or near this product.

 Do not use product if any parts are missing or damaged.

 Do not use substitute parts. Contact manufacturer should replacement parts be necessary.

 Before assembly and use, inspect product for damaged hardware, loose joints, missing pieces 

or sharp edges.

 Warning: hardware included with this product may have sharp points or edges. Assembly by an 

adult is required. Keep all loose hardware out of reach of children.

 Warning: small parts are a choking hazard for children. Make sure that all hardware is properly 

and tightly installed to prevent access to loose parts by children. Properly discard excess 
hardware after assembly to prevent access of loose parts to children. Properly discard all 
packing materials.

Important Information

Each one of our products is handmade, hand painted, and hand packaged. Minor imperfections may 
occur that are not manufacturing defects, but rather a result of the handcrafting process that makes 
our products unique and special.

Summary of Contents for MAST-3











Reviews: