background image

 
6)  Re-tighten the 7/16 bolts, making sure that the Auger End Piece Shaft still freely 

rotates over the Auger Drive Motor shaft. 

7)  Reinstall the screw and nut connecting the Auger Drive Motor shaft to the Auger 

shaft. 

        

WITH THE TRAEGER DIGITAL CONTROL, WHAT DIAL SETTING IS 
RECOMMENDED FOR STARTING THE GRILL?  

 

     The auto-start procedure is the same for all Grill Controls. With the Door open, turn 

the Switch/Dial ON and Temperature Dial to SMOKE. In approximately 2 minutes 
you will notice whitish-gray smoke coming out of the Grill as the Pellets ignite. After 
assuring the Pellets have ignited, close the Door and set the Temperature Dial to 
any cooking setting desired.   

 

HOW DO I PROTECT MY PAINT FINISH? 

 

1)  Use a protective Cover on the Grill and touch-up paint to repair any scratches. 

TRAEGER GRILL COVER to protect the Grill is highly recommended! Covers 
and touch-up paint are available from your local Traeger Dealer, or log on to 
our Web Site – 

www.traegergrills.com

2)  Every 90 days, use a high quality car wax on the outside surfaces of the Grill. ONLY 

APPLY WAX TO A COLD GRILL. 

 

WHERE CAN I GET A NEW PART FOR MY GRILL? 

 

Check with your Traeger Dealer. They may have the part in stock or can order the part 
for you. Or you can contact the Traeger Parts Department 

(SECTION SEVEN) 

to place 

an order. In either case, please provide your name, phone number, address, Model and 
Serial Number of the Grill (located on a label inside the Hopper Lid), along with the part 
identification. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for BBQ055















Reviews: