Traffic Logix SafePace 650 Installation Manual Download

Page: 17 / 19

Page 17

Operating your sign

Once mounted and powered, your sign can be connected to
using Bluetooth or Wi-Fi, and easily programmed and managed
or scheduled with our easy to use software.

For more information on operating and programming your sign, please refer to the SafePace® Pro User
Manual.
*Get the latest version at:

http://trafficlogix.com/customerarea/customerdownloads

Maintaining your sign

Replacing key internal sign components

The SafePace® 650 radar speed sign are comprised of the following key electronic components (and
respective quantities):

•

Controller Card (1)

•

Radar Head with controller (1)

•

BlueFin Bluetooth Controller (1)

•

VMFin VM Controller (1)

•

Combination Speed Violator Strobe/LED Matrix Display Board (1)

•

LED Matrix Display Boards (2)

•

Ambient Light Sensor (2)

WARNING

: Before ever doing any maintenance on a sign, it is critical that the

power is first turned off. This will prevent accidental electrical shock that can be
fatal and that can also damage electrical components.

If you suspect that you require a replacement of any of the above-mentioned components, please call

Technical Support

. If necessary, a Diagnostic Toolbox can be sent out to help trouble-shoot any issues

you may be having.

Summary of Contents for SafePace 650




















Search results

Summary of Contents for SafePace 650

Reviews:

Related manuals for SafePace 650

Brands by name

Popular brands

Traffic Logix SafePace 650, Installation Manual

Search results

Summary of Contents for SafePace 650

Reviews:

Related manuals for SafePace 650

Brands by name

Popular brands