background image

Removal and Installation

14

 COM-SVN003B-EN

When brazing, always use a nitrogen purge to prevent 
the formation of copper oxide contamination that can 
damage the compressor.

Electrical Connections

CSHW 047-089

The phases on the terminal block are color coded:

Red - PhaseL1

Blue - PhaseL2

None - PhaseL3

The CSHW compressor is designed for use with terminal 
plugs.

Before starting the compressor, check the electrical 
phasing with a phase sequence meter similar to an 
Ideal-Sperry Model 61-520.

WARNING

Hazardous Service Procedures!

Failure to follow all instructions in this manual and on 
the tags, stickers, and labels could result in death or 
serious injury.
Technicians, in order to protect themselves from 
potential electrical, mechanical, and chemical hazards, 
MUST follow precautions in this manual and on the 
tags, stickers, and labels, as well as the following 
instructions: Unless specified otherwise, disconnect all 
electrical power including remote disconnect and 
discharge all energy storing devices such as capacitors 
before servicing. Follow proper lockout/tagout 
procedures to ensure the power can not be 
inadvertently energized. When necessary to work with 
live electrical components, have a qualified licensed 
electrician or other individual who has been trained in 
handling live electrical components perform these 
tasks.

Figure 4.

Color coded compressor power plug

NOTICE

Compressor Damage!

Operating the compressor with improper phasing could 
cause compressor failure. Check phasing before starting 
compressor. 

Hermetic Feed 
through

Summary of Contents for CSHW047

























Reviews: