background image

Installer's Guide

ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES

Single Packaged, Cooling w/ Electric Heat, 
14 SEER, Convertible, 2

 

- 5 Ton, R-410A

4TCY4024 through 4TCY4060

WARNING:

 

HAZARDOUS VOLTAGE - DISCONNECT POWER and DISCHARGE  

 

                                              CAPACITORS BEFORE SERVICING

IMPORTANT — 

This Document is customer property. Please return to service information pack and give this Installer's Guide to the homeowner

upon completion of work.

SAFETY HAZARD!

Bodily injury can result from high voltage electrical com-

ponents, fast moving fans, and combustible gas. For 

protection from these inherent hazards during installation 

and service, the electrical supply must be disconnected 

and the main gas valve must be turned off. If operating 

checks must be performed with the unit operating, it is the 

technician's responsibility to recognize these hazards and 

proceed safely.

s

s

WARNING

SAFETY HAZARD!

This information is for use by individuals having adequate 

backgrounds of electrical and mechanical experience. 

Any attempt to repair a central air conditioning product 

may result in personal injury and/or property damage. 

The manufacturer or seller cannot be responsible for the 

interpretation of this information, nor can it assume any 

liability in connection with its use.

s

s

WARNING

18-EB26D1-16A-EN

WARNING!

This product can expose you to chemicals including lead, 

which are known to the State of California to cause cancer 

and birth defects or other reproductive harm. For more 

information go to www.P65Warnings.ca.gov

s

s

WARNING

Summary of Contents for 4TCY4024

























Reviews: