Trane IntelliPak WEHE Series Installation, Operation And Maintenance Manual Download

Page: 49 / 123

Installation

RT-SVX35H-EN

d. Do not run the AC low voltage wiring in the same

conduit with the high voltage power wiring.

Controls using DC Analog Input/Outputs

Before installing any connecting wiring between the unit
and components utilizing a DC analog input\output signal,
refer to

Figure 4, p. 19

Figure 8, p. 23

for the electrical

access locations provided on the unit and

Table 14

for

conductor sizing guidelines and;

a. Use standard copper conductor thermostat wire

unless otherwise specified.

b. Ensure that the wiring between the controls and the

unit's termination point does not exceed two and a
half (2.5) ohms/conductor for the length of the run.

Important:

Resistance in excess of 2.5 ohms per
conductor can cause deviations in the
accuracy of the controls.

c. Do not run the electrical wires transporting DC

signals in or around conduit housing high voltage
wires.

Units equipped with a Trane Communication Interface
(TCI), BACnet Communication Interface (BCI), or LonTalk
communication Interface (LCI) option which utilizes a
serial communication link;

a. Must be 18 AWG shielded twisted pair cable

(Belden 8760 or equivalent).

b. Must not exceed 5,000 feet maximum for each link.
c. Must not pass between buildings.

Constant Volume System Controls

Remote Panel w/o NSB BAYSENS110*

This electronic sensor features four system switch settings
(Heat, Cool, Auto, and Off) and two fan settings (On and
Auto) with four system status LED's. It is a manual or
automatic changeover control with dual setpoint
capability. It can be used with a remote zone sensor

BAYSENS077*. Refer to

Table 15, p. 52

for the

Temperature vs. Resistance coefficient.

Constant Volume Zone Panel - BAYSENS108*

This electronic sensor features four system switch settings
(Heat, Cool, Auto, and Off) and two fan settings (On and
Auto). It is a manual or automatic changeover control with
dual setpoint capability.

Variable Air Volume System Controls

VAV Changeover Contacts (5K87)

These contacts are connected to the RTM when daytime
heating on VAV units with internal or external hydronic
heat is required. Daytime (occupied) heating switches the
system to a CV type mode of operation. Refer to the unit
wiring diagram for the field connection terminals in the
unit control panel. The switch must be rated at 12 ma @ 24
VDC minimum.

Constant Volume or Variable Air Volume

System Controls

Remote Human Interface Module (5U66)

The Remote Human Interface module enables the
operator to set of modify the operating parameters of the
unit using it's 16 key keypad and view the operating status
of the unit on the 2 line, 40 character LCD screen without
leaving the building. However, the Remote Human
Interface module can not be used to perform any service
functions.
One remote panel is designed to monitor and control up to
four units providing each of the units are equipped with an
IPCB module. Use the installation instructions that
shipped with the module to install it, and the appropriate
illustrations in

Figure 27, p. 44

Figure 33, p. 57

connect it to the unit.

Remote Panel w/ NSB - BAYSENS119*

This 7 day programmable sensor features four periods for
Occupied\Unoccupied programming per day. Either one
or all four periods can be programmed. If the power is
interrupted, the program is retained in permanent
memory. If power is off longer than 2 hours, only the clock
and day may have to be reset.
The front panel allows selection of Occupied/Unoccupied
periods with two temperature inputs (Cooling Supply Air
Temperature and Heating Warm-up temperature) per
occupied period. The occupied cooling setpoint ranges

between 40°F and 80°F. The warm-up setpoint ranges
between 50°F and 90°F with a 2° deadband. The
Unoccupied cooling setpoint ranges between 45°F and
98°F. The heating setpoint ranges between 43°F and 96°F.

The liquid crystal display (LCD) displays zone temperature,
temperature setpoints, week day, time, and operational
mode symbols. The DIP switches on the subbase are used
to enable or disable applicable functions, i.e.; Morning
warm-up, economizer minimum position override during

Table 13. AC Conductors

Distance from Unit

to Control

Recommended

Wire Size

000 - 460 feet

18 gauge

461 - 732 feet

16 gauge

733 - 1000 feet

14 gauge

Table 14. DC conductors