background image

General Information

6

 CVRF-SVN005C-EN

Remove the existing chiller nameplate on the unit and relocate 
to the outside of the new control panel. Important information 
is contained on this existing nameplate that must be retained 
for future unit servicing. 

If nameplate cannot be removed and relocated, copy 
information from old nameplate onto new vinyl nameplate 
included in retrofit package.

Symbio™ Panel Conversion Kit 
Contents

Each Symbio™ panel conversion kit includes a pre-assembled 
control panel with a number of standard features and options 

installed, wired, bound, and tested, along with some device 
LLIDs shipped loose that require field installation and binding.
Before commencing the Symbio™ control retrofit, be sure to 
compare the data on the panel nameplate and ordering and 
shipping information to the data in the following tables to verify 
that the proper Symbio™ components were shipped. The 
tables are split into those components that are factory installed 
and those that are shipped loose and need to be field installed.
If an inspection of the conversion package reveals damage or 
material shortages, be sure to file these claims with the carrier 
immediately. Specify the extent of the damage or material 
shortages and be sure to notify the appropriate Trane 
representative. Do not install a damaged component or panel.

Table 2.

LLID legend and identification

(a)

 

LLID Name

Description

Part Number

Tracer® Adaptiview™ color display

MOD03183

LON

LonTalk

®

Communications interface for chillers

KIT18458, KIT; ECHELON MODULE FIELD INSTALL 
KIT

DAIO

Dual analog input and output

BRD04875

DBI

Dual low voltage binary input

BRD04873

DHVBI

Dual high voltage binary input

BRD04874

DRO

Dual relay output

BRD04878

HPRO

High power relay output

MOD01401

IGV

Inlet guide vane stepper actuator

ACT00680

Power supply

27 Vac to 24 Vdc for bus power supply

BRD02102

Pressure sensor

Low pressure range, 0 to 50 psia

TDR00733

Pressure sensor

High pressure range, 0 to 475 psia

TDR00734

Pressure transducer

Danfoss pressure transducer, 475 PSI 

7/16-20 NUF

TDR00735

QRO

Quad relay output

BRD04879

Starter module

Trane control board, starter module

BRD04877

Starter module power supply

110 Vac/24 Vdc power supply

PWR00147

Starter module on sub plate without power supply or LV 
PTs

Starter sub-panel for unit mount medium voltage 

starters

018504210100

Starter module on sub plate without power supply with 
LV PTs

Starter sub-panel for remote mount medium voltage 

starters

018504330100

Starter module on sub plate with power supply without 
LV PTs

Starter sub-panel for unit mount low voltage starters 018504220100

Starter module on sub plate with power supply and LV 
PTs

Starter sub-panel for remote mount low voltage 

starters

018504350100

AFD starter nodule on sub plate without power supply 
or LV PTs

Assembly for unit mount UCP2 AFDB, AFDC, and non-
communicating AFDH

018504340100

AFD starter nodule on sub plate with power supply 
without LV PTs

Assembly for remote mount UCP2 AFDB, AFDC, and 
non-communicating AFDH

018504370100

Temp sensor

Low range temperature sensor

SEN02133

Triac

Dual triac output

BRD04876

TWTI

Triple winding temperature input

MOD02462

Symbio™ controller

MOD02979

Summary of Contents for Symbio CVRF

















































Reviews: