background image

Installation  . . . . . . . . . . . . . . . . . . . . .2
Operation  . . . . . . . . . . . . . . . . . . . . . .6
Cable Specifications  . . . . . . . . . . . . . .7
Technical Specifications  . . . . . . . . . . .8
Troubleshooting  . . . . . . . . . . . . . . . . .9
Compliance Information  . . . . . . . . .12

* Typical maximum cable distance. Actual

distance is dependent upon the physical
characteristics of the network.

CSDTF3027-115

75 ohm BNC coax
100 m

(328 ft.)*

ST, 1300 nm multimode
5 km

(3.1 miles)*

Part Number

Port One - Copper

Port Two - Duplex Fiber-Optic

CSDTF3011-115

75 ohm BNC coax
100 m

(328 ft.)*

ST, 850 nm multimode
2 km

(1.2 miles)*

CSDTF3012-115

75 ohm BNC coax
100 m 

(328 ft.)*

ST, 1310 nm single mode
8 km

(4.8 miles)*

CSDTF3013-115

75 ohm BNC coax
100 m 

(328 ft.)*

SC, 850 nm multimode
2 km

(1.2 miles)*

CSDTF3014-115

75 ohm BNC coax
100 m

(328 ft.)*

SC, 1310 nm single mode
20 km 

(12.4 miles)*

CSDTF3015-115

75 ohm BNC coax
100 m

(328 ft.)*

SC, 1310 nm single mode
40 km

(24.8 miles)*

CSDTF3016-115

75 ohm BNC coax
100 m

(328 ft.)*

SC, 1310 nm single mode
60 km 

(37.3 miles)*

CSDTF3017-115

75 ohm BNC coax
100 m

(328 ft.)*

SC, 1550 nm single mode
80 km

(49.7 miles)*

CSDTF3018-115

75 ohm BNC coax
100 m

(328 ft.)*

MT-RJ, 1300 nm multimode
2 km

(1.2 miles)*

CSDTF3022-115

75 ohm BNC coax
100 m

(328 ft.)*

ST, 1310 nm single mode
15 km 

(9.3 miles)*

CSDTF3025-115

75 ohm BNC coax
100 m

(328 ft.)*

MT-RJ, 1310 nm single mode
20 km

(12.4 miles)*

User’s Guide

CSDTF30xx-11x

Slide-in-Module Device

E1 with Remote Management

Coax (BNC) to Fiber

Transition Networks CSDTF30xx-11x series Device,
designed to be installed into the Transition Networks

PointSystem™

chassis, encodes and decodes E1 coax copper

signals over fiber optic cable to extend the distance and
transmission reliability of high-speed E1 data traffic.  The
CSDTF30xx-11x is framing independent 

(as ESF vs. D4)

and supports all common line codes

(e.g., AMI, B8ZS,

HDB3).

The CSDTF30xx-11x is designed to be installed in pairs.  For example, install

one CSDTF3011-115 as the local Device and another CSDTF3011-115 as the remote
Device.

Summary of Contents for CSDTF3011-115








Reviews: