background image

Transition Networks 

 

 

 

 

 

 

   

 

 E-MCR-05 User Guide

 

33392 Rev. C 

https://www.transition.com/ 

Page 11 of 12 

Return Instructions 

Send the defective product postage and insurance prepaid to the following address:  

Transition Networks, Inc. 
10900 Red Circle Drive 
Minnetonka, MN 55343 USA 
Attn: RETURNS DEPT: CRA/RMA # ___________  

Failure to properly protect the product during shipping may void this warranty. The return authorization number must be 
written on the outside of the carton to ensure its acceptance. We cannot accept delivery of any equipment that is sent to us 
without a CRA or RMA number.  

CRA’s a

re valid for 60 days from the date of issuance. An invoice will be generated for payment on any unit(s) not returned 

within 60 days.  

Upon completion of a demo/ evaluation test period, units must be returned or purchased within 30 days. An invoice will be 
generated for payment on any unit(s) not returned within 30 days after the demo/ evaluation period has expired.  

The customer must pay for the non-compliant product(s) return transportation costs to Transition Networks for evaluation 
of said product(s) for repair or replacement. Transition Networks will pay for the shipping of the repaired or replaced in-
warranty product(s) back to the customer (any and all customs charges, tariffs, or/and taxes are the customer's 
responsibility).  

Before making any non-warranty repair, Transition Networks requires a $200.00 charge plus actual shipping costs to and 
from the customer. If the repair is greater than $200.00, an estimate is issued to the customer for authorization of repair.  
If no authorization is obtained, or the product is deemed not repairable, Transition Networks will retain the $200.00 service 
charge and return the product to the customer not repaired. Non-warranted products that are repaired by Transition 
Networks for a fee will carry a 180-day limited warranty. All warranty claims are subject to the restrictions and conventions 
set forth by this document.  

Transition Networks reserves the right to charge for all testing and shipping incurred, if after testing, a return is classified as 
"No Problem Found."  

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE 
EXPRESSED OR IMPLIED. TRANSITION NETWORKS IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR 
CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY. AUTHORIZED 
RESELLERS ARE NOT AUTHORIZED TO EXTEND ANY DIFFERENT WARRANTY ON TRANSITION NETWORKS'S BEHALF. 
 

Record of Revisions 

 

Rev 

Date 

Notes 

5/12/08 

Initial release. 

9/7/10 

Update text and graphics. 

8/20/19 

Update to current build and format.  

Trademark Notices

: All trademarks and registered trademarks are the property of their respective owners. 

Copyright Restrictions

: © 2010-2019 Transition Networks. All rights reserved. No part of this work may be 

reproduced or used in any form or by any means - graphic, electronic or mechanical - without written 
permission from Transition Networks. 

Summary of Contents for E-MCR-05













Reviews: