Transition Networks E-TBT-HB-1002 User Manual Download | Manualshive

Page: 1 / 10

background image

24 Port 10BaseT Ethernet Hub

Model E-TBT-HB-1002

Users Manual

Manual #7306

Specifications

Warranty: 2 years

Power Supply: Internal Power Supply, Input AC 100 -

250 VAC, 47 - 63 Hz, 40W Max

Environment: 0 - 70˚C, 5% - 90% humidity non-con-

densing, 0 - 10,000 ft. altitude

Dimensions: Free standing (rack mount adapters

included) 19" W x 6.25" D x 3.4" H
Desk top - 17" W x 6.25" D x 3.4" H

Accessories: Rack mounting tabs included for stand-

ard 19" wall racks
Rubber feet for free standing

Safety Approvals: UL Listed

C-UL Approved (Canadian Safety)

1
2
3
...
»

Summary of Contents for E-TBT-HB-1002











Reviews:

No comments

Related manuals for E-TBT-HB-1002

xStack DGS-3612G series

Brand: D-Link Pages: 546

xStack DGS-3400 Series

Brand: D-Link Pages: 326

xStack DGS-3612G series

Brand: D-Link Pages: 493

xStack DGS-3400 Series

Brand: D-Link Pages: 540

DXS-3326GSR - xStack Switch - Stackable

Brand: D-Link Pages: 354

DGS-1024D - Switch

Brand: D-Link Pages: 16

DGS-1016D - Switch

Brand: D-Link Pages: 44

DES-6000 Series

Brand: D-Link Pages: 3

DES-5024 - Switch

Brand: D-Link Pages: 2

DES-3828 - xStack Switch - Stackable

Brand: D-Link Pages: 3

Brand: D-Link Pages: 192

Brand: D-Link Pages: 9

Brand: D-Link Pages: 110

Brand: D-Link Pages: 10

Brand: D-Link Pages: 17

Brand: D-Link Pages: 4

Brand: D-Link Pages: 9

Brand: D-Link Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands