Transition Networks PowerStar III Manual Download | Manualshive

Page: 10 / 12

background image

12

7

PowerStar™ III

3. Slide PowerStar™ III cover back approximately one inch to

disengage cover from chassis.

4. Carefully lift PowerStar™ III cover and remove.

5. Using needle nose pliers with insulated handle and referring to

reference material on the next page, move jumpers as required
to change factory default active pin settings to active pin
settings for the site.

«
...
8
9
10
11
12
»

Summary of Contents for PowerStar III













Reviews:

No comments

Related manuals for PowerStar III

Brand: AMEC Pages: 35

Brand: VEAB Pages: 6

Brand: Gasmate Pages: 20

Brand: L.B. White Pages: 20

Brand: DeLonghi Pages: 4

Brand: TERMA Pages: 2

GUARDIAN Smart Sense AD250

Brand: L.B. White Pages: 24

Brand: MILL Pages: 10

Brand: Scarlett Pages: 8

Brand: Space-Ray Pages: 15

Brand: Aeotec Pages: 5

Brand: Vulpes Electronics Pages: 12

Vasco Tulipa T1/NVR1

Brand: Arbonia Pages: 2

Brand: KASTOR Pages: 24

Brand: Teesa Pages: 44

Brand: Profile Pages: 19

Brand: Quality Heating Pages: 43

Brand: VEAB Heat Tech Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands