background image

TRAXXAS RALLY • 13

6

Remember, always turn the 
TQ transmitter on first and 
off last to avoid damage to 
your model. 

Automatic Fail-Safe

The TQ 2.4GHz transmitter 
and receiver are equipped 
with an automatic fail-
safe system that does not 
require user programming. 
In the event of signal loss 
or interference, the throttle 
will return to neutral and 
the steering will hold its 
last commanded position. If 
Fail-Safe activates while you 
are operating your model, 
determine the reason for 
signal loss and resolve the 
problem before operating 
your model again.

When rechargeable batteries 
begin to lose their charge, 
they will fade much faster 
than alkaline dry cells. Stop 
immediately at the first sign 
of weak batteries. Never turn 
the transmitter off when the 
battery pack is plugged 
in. The model could run out 
of control.

TQ RADIO SYSTEM RULES 

  Always turn your TQ 2.4GHz transmitter on first and off last. This 

procedure will help to prevent your model from receiving stray 
signals from another transmitter, or other source, and running out 
of control. Your model has electronic fail-safes to prevent this type 
of malfunction, but the first, best defense against a runaway model 
is to always turn the transmitter on first, and off last.

  In order for the transmitter and receiver to bind to one another, 

the receiver in the model must be turned on within 20 seconds 
of turning on the transmitter. The transmitter LED will flash fast 

red indicating a failure to link. If you miss it, simply turn off the 
transmitter and start over.

  Always turn on the transmitter before plugging in the battery.

  Always use new or freshly charged batteries for the radio 

system. 

Weak batteries will limit the radio signal between the 

receiver and the transmitter.

 Loss of the radio signal can cause 

you to lose control of your model.

TQ 2.4GHz RADIO SYSTEM BASIC ADJUSTMENTS

Throttle Neutral Adjustment 

The throttle neutral adjustment is located 
on the transmitter face and controls the 
forward/reverse travel of the throttle trigger. 
Change the adjustment by pressing the 
button and sliding it to the desired position. 
There are two settings available:

50/50

: Allows equal travel for both forward and reverse.

70/30

: Allows more forward travel (70%) and less reverse travel (30%).

Note: We strongly recommend to leave this control in its factory 
location until you become familiar with all the adjustments and 
capabilities of your model. 

To change the throttle neutral adjust 

position, turn the transmitter off before adjusting the neutral 
position. 

You will need to reprogram your electronic speed control 

to recognize the 70/30 setting.

 Turn to ESC Setup Programming on 

page 16 for instructions.

Steering Trim 

The electronic steering trim located on the face of the 
transmitter adjusts the neutral (center) point of the 
steering channel. 

Multi-Function Knob

The Multi-Function knob can be programmed to 
control a variety of functions. From the factory, the 
Multi-Function knob controls steering sensitivity, 
also known as exponential or “expo.” When the knob 
is turned counterclockwise all the way to the left 
(default position), expo is off and steering sensitivity will be linear 
(the most commonly used setting). Turning the knob clockwise will 
“add expo” and decrease the steering sensitivity in the initial range 
of steering wheel travel left or right from center. For more detail on 
steering exponential, refer to page 15.

TQ 2.4GHz RADIO SYSTEM CONTROLS

Always turn your

transmitter on first.

Turn on the model.

1

2

Plug in the battery.

3

TRAXXAS TQ 2.4GHz RADIO & VELINEON POWER SYSTEM

THROTTLE TRIM

100

100

0

0

THROTTLE TRIM

100

100

0

0

Summary of Contents for 18 Kyle Busch

































Reviews: