background image

SLASH VXL • 19

Now it’s time to have some fun! This section contains instructions on 
driving and making adjustments to your model. Before you go on, 
here are some important precautions to keep in mind. 
•  Allow the model to cool for a few minutes between runs. This is 

particularly important when using high-capacity battery packs 
that allow extended periods of running. Monitoring temperatures 
will extend the lives of the batteries and motors. See page 25 for 
information on monitoring temperatures.

•  Do not continue to operate the model with low batteries or you 

could lose control of it. Indications of low battery power include slow 
operation, sluggish servos (slow to return to center), or ESC shutdown 
due to the Low-Voltage Detection circuitry. Stop immediately at the 
first sign of weak batteries. When the batteries in the transmitter 
become weak, the power light will begin to flash red. Stop 
immediately and install new batteries.

•  Do not drive the model at night, on public streets, or in large 

crowds of people.

•  If the model becomes stuck against an object, do not continue to run 

the motor. Remove the obstruction before continuing. Do not push or 
pull objects with the model.

•  Because the model is controlled by radio, it is subject to radio 

interference from many sources beyond your control. Since radio 
interference can cause momentary losses of control, allow a safety 
margin of space in all directions around the model in order to 
prevent collisions.

•  Use good, common sense whenever you are driving your model. 

Intentionally driving in an abusive and rough manner will only result 
in poor performance and broken parts. Take care of your model so 
that you can enjoy it for a long time to come.

•  When using the supplied optional pinion for top-speed running, 

limit your driving to paved surfaces only. Running in grass and 
off-road could cause excessive loads on the electrical system in the 
model.

•  High-performance vehicles produce small vibrations that may 

loosen hardware over time.  Frequently check wheel nuts and 
other screws on your vehicle to ensure that all hardware remains 
properly tightened.  

About Run Time

A large factor affecting run time is the type and condition of your 
batteries. The milliamp hour (mAh) rating of the batteries determines 
how large their “fuel tank” is. A 3000mAh battery pack will theoretically 
run twice as long as a 1500mAh sport pack. Because of the wide 
variation in the types of batteries that are available and the methods 
with which they can be charged, it’s impossible to give exact run times 
for the model.
Another major factor that affects run time is how the model 
is driven. Run times may decrease when the model is driven 
repetitively from a stop to top speed and with repetitive hard 
acceleration.

Tips for Increasing Run Time

• Use batteries with the highest mAh rating you can purchase.
• Use a high-quality peak-detecting charger. 
• Read and follow all maintenance and care instructions provided by 

the manufacturer of your batteries and charger.

• Keep the VXL-3s cool. Get plenty of airflow across the ESC heat 

sinks. 

• Use the correct Low-Voltage Detection setting for your battery 

(see page 17). Low-Voltage Detection can be off for maximum 
NiMH battery runtime. Never use LiPo batteries while Low-Voltage 
Detection is turned off. 

• Lower your gear ratio. Installing a smaller pinion or larger spur gear 

will lower your gear ratio, causing less power draw from the motor 
and battery, and reducing overall operating temperatures.

• Maintain your model. Do not allow dirt or damaged parts to cause 

binding in the drivetrain. Keep the motor clean.

mAh Ratings and Power Output

The mAh rating of the battery can affect your top-speed 
performance. The higher capacity battery packs experience less 
voltage drop under heavy load than low mAh rated packs. The 
higher voltage potential allows increased speed until the battery 
begins to become discharged.

RUNNING IN WET CONDITIONS

Your new Traxxas model is designed with water-resistant features 
to protect the electronics in the model (receiver, servos, electronic 
speed control). This gives you the freedom to have fun driving your 
model through puddles, wet grass, snow, and through other wet 
conditions. Though highly water resistant, the model should not 
be treated as though it is submersible or totally 100% waterproof. 

DRIVING YOUR MODEL

9

Summary of Contents for 5807L

































Reviews: