XO-1
•
29
2. Download and install the Traxxas Link application from the App Store.
3. Open the Traxxas Link application and touch the Unlock icon.
Follow the prompts to register your model. You will be asked to
accept the terms of use and provide an e-mail address.
Make certain you can access the address you provide.
4. The application will send you an e-mail to confirm your
registration information. Open the e-mail and follow the
confirmation link.
5. The Traxxas Link application will now permit you to unlock the
power system’s full power capability. Touch the Unlock icon to
unlock the model.
You may lock the power system at any time without a connection
to the internet. Lock the power system anytime the model will be
stored to prevent top speed access by unauthorized drivers. You will
need your e-mail address and an internet connection to unlock the
power system again later. Supplying your e-mail address will prevent
you from having to re-register the product.
Installing Your Mobile Device
The TQi
™
Docking Base has a unique clamping mechanism that
allows the Apple
®
iPhone
®
and iPod touch
®
to be easily installed
and removed. The clamp’s self-adjusting design allows it to
accommodate the wide variety of protective cases available for
Apple products. Follow these steps to install your mobile device:
1. Swing the Docking Base Clamp
lever from position A (locked) to
position B (unlocked).
2. Install your mobile device by
sliding it onto the connector.
3. Ensure your mobile device
is parallel with the Docking
Base. Slide the included
foam pads beneath the
mobile device so it is held
parallel with the docking
base when supported
by the pads. The pads
have thicknesses of 1,
2, 3, and 4mm; choose
the best combination for your device and case (if used). See the
sidebar chart to find the
correct pad combination
for iPhone and iPod
touch models without
accessory cases.
4. Make certain your
mobile device slides
directly onto the connector when installed over the foam pads.
When you are satisfied with the fit, peel the backing from the foam
pads and apply them to the Docking Base.
5. Close the Docking Base Clamp by moving it to position A. Confirm
your mobile device is snug and securely held in place.
Optional
: The Docking Base Clamp’s ‘fingers’ have soft gripper pads on
them to hold un-cased devices. If your device is in a soft rubber case, the
gripper pads may be removed for easier device installation and removal.
DRIVING 100MPH
The XO-1 is the world’s first Ready-To-Race radio controlled car, capable
of speed that exceeds 100mph.
Driving at 100mph should never be
done casually, without careful thought and preparation. Operating
the XO-1 in a careless, unsafe manner, without adequate care and
preparation, can result in collisions with catastrophic consequences
such as serious injury or death. Know your limits and act accordingly.
ALWAYS confirm each item on this checklist before operating your
vehicle at maximum speed.
OPERATING THE XO-1 AT MAXIMUM SPEED
TQi Docking Base foam pad
combination recommendations
(without accessory cases):
iPod touch 3rd Generation
4mm + 3mm (7mm total)
iPod touch 4th Generation
4mm + 3mm + 2mm (9mm total)
iPhone 3GS
3mm + 2mm (5mm total)
or
4mm + 1mm (5mm total)
iPhone 4
4mm + 3mm + 1mm (8mm total)
A
B
1
2
3
q
Complete the inspection steps on page 23.
q
Confirm the tires are firmly bonded to the rims and not
excessively worn.
q
Confirm you are on a
closed course
that is free of
bystanders, vehicles, and obstructions.
q
Confirm you have adequate radio range by performing a
range test as described on page 16.
q
Confirm the air is calm. Do not attempt full-speed
operation in windy conditions.
q
Operate the vehicle from a location that is off of the
running surface. Choose a location that allows you to
stand behind a wall or other barricade.
To experience all the features
of the TQi with Docking Base,
you will need an Apple iPhone
(3GS, 4, 4S) or iPod touch (3rd
generation). Your Traxxas TQi
transmitter is also compatible
with the iPhone 5 series (5, 5S, 5C)
or iPod touch (5th generation)
when used with the Lightning to
30-pin adapter. You will also need
the Traxxas Link
®
application,
which you can download from the
Apple App Store
™
.
