background image

E-REVO VXL BRUSHLESS • 3

BEFORE YOU PROCEED

Traxxas
6250 Traxxas Way
McKinney, Texas 75070
Phone: 972-549-3000
Toll-free 1-888-TRAXXAS

Internet
Traxxas.com
E-mail: support@Traxxas.com

Entire contents ©2018 Traxxas. 
Traxxas, Ready-To-Race, Ready-To-
Win, E-Revo, E-Revo VXL, Velineon, 
and ProGraphix are trademarks 
or registered trademarks of 
Traxxas. Other brand names and 
marks are the property of their 
respective holders and are used 
only for purposes of identification. 
No part of this manual may be 
reproduced or distributed in print 
or electronic media without the 
express written permission of 
Traxxas. Specifications are subject 
to change without notice.

Carefully read and follow all instructions in this and any 
accompanying materials to prevent serious damage to your  
model. Failure to follow these instructions will be considered  
abuse and/or neglect.
Before running your model, look over this entire manual and examine 
the model carefully. If for some reason you decide it is not what 
you wanted, then do not continue any further. 

Your hobby dealer 

absolutely cannot accept a model for return or exchange after it 
has been run.

Warnings, Helpful Hints, & Cross-References

Throughout this manual, you’ll notice warnings and helpful hints 
identified by the icons below. Be sure to read them!

An important warning about personal safety or avoiding
damage to your model and related components. 

Special advice from Traxxas to make things easier  
and more fun.

Refers you to a page with a related topic.

SUPPORT

If you have any questions about your model or its operation, 
call the Traxxas Technical Support line toll-free at: 

1-888-TRAXXAS (1-888-872-9927)

*

Technical support is available Monday through Friday from 8:30am 
to 9:00pm central time. Technical assistance is also available at Traxxas.
com. You may also e-mail customer support with your question at 
support@Traxxas.com. Join thousands of registered members in our 
online community at Traxxas.com.
Traxxas offers a full-service, on-site repair facility to handle any  
of your Traxxas service needs. Maintenance and replacement  
parts may be purchased directly from Traxxas by phone or online  
at Traxxas.com. You can save time, along with shipping  
and handling costs, by purchasing replacement parts from your  
local dealer.
Do not hesitate to contact us with any of your product support needs. 
We want you to be thoroughly satisfied with your new model!

*Toll-free support is available to U.S. residents only.

1

Summary of Contents for 86086-4









































Reviews: