background image

14 • TRAXXAS

4,5

TRAXXAS TQ 2.4GHz RADIO SYSTEM

INSTALLING THE BATTERY PACK

Place the battery pack into the battery compartment of the model 
and then place the battery hold-down over the posts. Secure the
battery hold-down with body clips in the holes in the posts.  Do not 
connect the battery pack yet.

The Traxxas High-Current Connector

Your model is equipped with the Traxxas High-

Current Connector. Standard connectors restrict 
current flow and are not capable of delivering 
the power needed to maximize the output of 
the XL-5. The Traxxas connector’s gold-plated terminals with large 
contact surfaces ensure positive current flow with the least amount of 
resistance. Secure, long-lasting, and easy to grip, the Traxxas connector is 
engineered to extract all the power your battery has to give.

SETTING UP THE ANTENNA

The receiver antenna and antenna tube must be properly installed 
before operating your model. Follow these steps to install the 
antenna and antenna tube:
1. Slide the antenna wire into the antenna tube to its full extent. 

When fully inserted, the wire should reach to approximately  
1/2 inch below the tube cap. Do not leave any slack in the 
antenna wire.

2. Insert the base of the antenna tube into the molded post on the 

chassis. Take care not to crimp the antenna wire. Do not bend or 
kink the antenna wire!  Do not shorten the antenna tube. See the 
side bar for more information.

To prevent loss of radio range, 
do not kink or cut the black wire, 
do not bend or cut the metal tip, 
and do not bend or cut the white 
wire at the end of the metal tip.

Correct

No

No

No

No

Stampede

Rustler and Bandit

Antenna 

Mount

Antenna 

Mount

Battery iD

Your model’s included battery 
pack is equipped with Traxxas 
Battery iD. This exclusive 
feature allows Traxxas battery 
chargers (sold separately) 
to automatically recognize 
connected battery packs 
and optimize the charge 
settings for the battery. 
This eliminates the need to 
worry over charger settings 
and menus for the easiest 
and safest charging solution 
possible. Visit Traxxas.com to 
learn more about this feature 
and available Traxxas iD 
chargers and batteries.

Summary of Contents for Bandit 24054





























Reviews: