WEARING THE TREBLAB EARPHONES
To properly wear the ear units:
1
Identify the Left and Right earphones. Look above
the ear bud for an R or L.
2
Place the earphone with the ear bud in your ear
canal and tuck the “wings” into the front ear fold
facing up.
PAIRING LEFT AND RIGHT CHANNELS
Before you can connect to a device, you need to pair
the left and right earphones:
1
Ensure the Bluetooth on your device is turned off.
If it is not, only the left earphone will pair.
2 Start by pressing on both earphones at the same
time for up to 10 seconds. You will hear an audible
cue saying
Power On
and both ear units will be
flashing red and blue. Release when this happens.
3
Once paired to each other, you will hear a single
beep on the right channel. Another cue will be heard
stating
Connected
and then
Left Channel
and
Right
Channel
confirmation checks.
4
After the confirmation checks, you will hear a single
beep in the left channel and the audible cue stating
the earphone is
Pairing
. The left ear bud will rapidly
flash blue and red. The right will blink once every
5 seconds.
PAIRING A BLUETOOTH DEVICE
To pair your Bluetooth device:
1
Activate the Bluetooth feature on your device and
search for Bluetooth devices (check your device’s
manual if you’re unsure how to do this).
2 Select
TREBLAB X11
from the device list.
3
If asked a passcode, enter
0000
or
1234
and the
earphones will then connect to your device.
4
After pairing successfully, the
LED indicator
will
flash blue and you will hear a double beep and hear
Pairing Successful
and
Connected
. You can then
answer the phone or listen to music.
5
The next time you switch on the earphones, they will
automatically search for and attempt to connect to
the last paired device.
RE-PAIRING OR PAIRING NEW DEVICES
The
TREBLAB
can only be paired to one device. If you
want to use the
TREBLAB
to listen to another device or
when you are re-pairing to the same device:
1
Ensure the Bluetooth is turned off on any previously
paired devices.
2
Pair the ear buds. See
Pairing the Left and Right
Channels
.
2
Pair to the Bluetooth device. See
Pairing a
Bluetooth device
.
TROUBLESHOOTING
If you cannot hear audio from your device, please
try the following:
1 Ensure that the earphones are fully charged,
switched on, paired with and connected to your
device.
2 Check that the earphones are within 30 feet / 10
meters of your device and that there are no obstruc-
tions (such as walls or other electronic devices)
between the earphones and device.
3 Only one device may be paired to these earphones
at the same time, so please ensure there are no
conflicting Bluetooth devices trying to connect to
the earphones.
If the earphones will not switch off, they can be
reset back to normal by charging them.
If you receive an intermittent signal, please
ensure the earphones are fully charged before
continuing use.
If you do not use the earphones for longer than 3
minutes while not connected to a device, they will
automatically power off to conserve power.
SAFETY RULES
Never disassemble or modify your headset for any
reason. Doing this may cause the headset to
malfunction or become combustible. The damage to
your device can void your manufacturer’s warranty.
Do not allow your device to get wet - liquids can
cause serious damage. Water damage to your
device can void your manufacturer’s warranty.
Avoid exposing your device to very cold or very hot
temperatures (below 37F/3C
o
or above 112F/45C
o
).
Extreme temperature can cause the deformation of
the device and reduce the charging and life of your
device.
Avoid using your device’s light close to the eyes of
children or animals.
Do not use the device during a thunderstorm.
Thunderstorms can cause the device to malfunction
and increase the risk of electric shock.
NOTE: Do not charge your headset for much longer
than 2 hours at a time, because this can lead to
reduction in battery capacity and can void your
manufacturer’s warranty.
Use only the provided USB/micro USB cable.
Excessive sweating may damage the product. Make
sure to wipe the headphones dry before charging.
BATTERY INFORMATION
Your device is powered by a rechargeable battery.
Unplug the charger from the electrical plug and the
device when not in use.
If left unused, a fully charged battery will lose its
charge over time. We recommend a full charge
twice a month to ensure battery integrity.
Please do not leave the device in hot or cold places,
such as in a closed car in summer or winter
conditions because this will reduce the capacity
and lifetime of the battery.
Do not dispose of the batteries in a fire as they may
explode. Batteries may also explode if damaged.
We really appreciate that you chose
TREBLAB
as your
trusted brand of Bluetooth earphones and sincerely
hope you enjoy the great sound and comfort
TREBLAB
provides. We love making our customers happy by
providing true value with our products.
If for any reason you are not completely satisfied with
your purchase, let us know immediately and we will do
everything to make sure you are happy.
