Trelawny TFP200 Operation & Maintenance Manual Download

Page: 9 / 10

PARTS LIST Continued

ITEM

Part Number

DESCRIPTION

ITEM

Part Number

DESCRIPTION

OTHER PARTS NOT SHOWN IN EXPLODED VIEW

320.9500

Air Motor

320.9141

5.5Hp Honda Engine

320.9142

110v 50Hz Electric Motor

320.9150

Spacer Plate (Electric) x 2 required

320.9146

220v 50/60hz Electric Motor

320.9147

220v 50/60hz Electric Starter

320.9805

Deadmans Handle Assembly (Prior 11.2009)

320.9300

M5 x 50 Screws for Deadmans Handle x 2

required

320.9160

Electric Motor 3hp 220/400v 3ph 50/60

320.9305

M5 Nyloc Nuts for Deadmans Handle x 2

required

320.9161

Electric Starter 3hp 380/440v 3ph

320.9310

M5 Plain Washer x 4 required

320.9164

Electric Starter 3ph 50/60hz

320.9165

Electric Motor 110v 1ph 60hz

320.9167

Electric Motor 110v 1ph 50hz

345.9805

Deadmans Handle Assembly (after 11.2009)

320.9168

Starter 110v 3ph 60hz

320.9169

Electric Motor 220v 1ph 60hz

320.9136

Hand Wheel Handle

320.9171

Electric Motor 220v 3ph 60hz

320.9198

Electric Motor 220v 3ph 60hz UL approved

841.2102

110v 32amp Lead Plug (Yellow)

841.2104

240v 16amp Lead Plug (Blue)

841.2106

415v Lead Plug (Red)

841.2640A

Overload Replay 230v only (RW27D17)

841.2640B

Contactor (CWM18.10 230v only)

Summary of Contents for TFP200











Search results

Summary of Contents for TFP200

Reviews:

Related manuals for TFP200

Brands by name

Popular brands

Trelawny TFP200, Operation & Maintenance Manual

Search results

Summary of Contents for TFP200

Reviews:

Related manuals for TFP200

Brands by name

Popular brands