background image

EN - T18S/BJ

EN - T18S/BJ

-15-

-14-

The tool will automatically turn off if the Electronic 
Protection System engages.

Battery Charging Indoors 

This charger is designed to be used indoors. We do not 
recommend that it is used inside your home. Ideally 
batteries should be charged on a bench in a workshop, 
garage or shed. If the charging operation is to be carried 
out in your home the area must be well ventilated and 
the charger must be placed on a non combustible 
surface ensuring that the ventilation slots are not 
blocked.

Wall Mounting 

These chargers are designed to be wall mountable or to 
sit upright on a table or work surface. If wall mounting, 
locate the charger within reach of an electrical outlet, 
and away from a corner or other obstructions which 
may impede air flow. Use the back of the charger as a 
template for the location of the mounting screws on the 
wall. Mount the charger securely using suitable fixings 
depending on wall type, a head diameter of 7 – 9mm 
and length of 25mm is recommended. Leave a suitable 
length of the screw exposed to allow the charger to be 
fitted. Align the slots on the back of the charger with the 
exposed screws and fully engage them in the slots.

Charger Cleaning Instructions

 WARNING: 

Shock hazard. Disconnect the 

charger from the AC outlet before cleaning. Dirt and 
grease may be removed from the exterior of the charger 
using a cloth or soft non-metallic brush. Do not use 
water or any cleaning solutions. Never let any liquid get 
inside the tool; never immerse any part of the tool into 
a liquid.

Battery Packs 

  

 
Important Safety Instructions for All Battery Packs

When ordering replacement battery packs, be sure to 
include product reference and voltage. 

The battery pack is not fully charged out of the carton. 
Before using the battery pack and charger, read 
the safety instructions below. Then follow charging 
procedures outlined.

READ ALL INSTRUCTIONS 

• 

Do not charge or use battery in explosive 
atmospheres, such as in the presence of 
flammable liquids, gases or dust. 

Inserting or 

removing the battery from the charger may ignite the 
dust or fumes.

• 

Never force battery pack into charger. Do not 
modify battery pack in any way to fit into a non-
compatible charger as battery pack may rupture 
causing serious personal injury.

• Charge the battery packs only in Trend chargers.
• 

DO NOT 

splash or immerse in water or other liquids.

• 

Do not store or use the tool and battery pack 
in locations where the temperature may fall 
below 4ºC (34ºF) (such as outside sheds or metal 
buildings in winter), or reach or exceed 40ºC 
(104ºF) (such as outside sheds or metal buildings 
in summer).

• 

Do not incinerate the battery pack even if it is 
severely damaged or is completely worn out. 

The 

battery pack can explode in a fire. Toxic fumes and 
materials are created when lithium-ion battery packs 
are burned. 

• 

If battery contents come into contact with the 
skin, immediately wash area with mild soap and 
water. 

If battery liquid gets into the eye, rinse water 

over the open eye for 15 minutes or until irritation 
ceases. If medical attention is needed, the battery 
electrolyte is composed of a mixture of liquid organic 
carbonates and lithium salts. 

• 

Contents of opened battery cells may cause 
respiratory irritation. 

Provide fresh air. If symptoms 

persists, seek medical attention.

 WARNING: 

Burn hazard. Battery liquid 

may be flammable if exposed to spark or flame.

 WARNING: 

Never attempt to open the 

battery pack for any reason. If battery pack case is 
cracked or damaged, do not insert into charger. Do 
not crush, drop or damage battery pack. Do not use a 
battery pack or charger that has received a sharp blow, 
been dropped, run over or damaged in any way (i.e., 
pierced with a nail, hit with a hammer, stepped on). 
Electric shock or electrocution may result. Damaged 
battery packs should be returned to service centre for 
recycling.

 WARNING: 

Fire hazard. Do not store or 

carry the battery pack so that metal objects can 
contact exposed battery terminals. 

For example, 

do not place the battery pack in aprons, pockets, tool 
boxes, product kit boxes, drawers, etc., with loose nails, 
screws, keys, etc.

 CAUTION: 

When not in use, place tool 

on its side on a stable surface where it will not 
cause a tripping or falling hazard.

 Some tools with 

large battery packs will stand upright on the battery pack 
but may be easily knocked over.

 

Battery Operation 

 

Charge Status  

To display the amount of charge left in the battery, press 
the charge level indicator button, (Fig.2). Fig. 2a shows 
the relation between the LED indication and charge left.

NOTE:

 The battery charge level indicator is only an 

indication of the charge left on the battery pack. It does 
not indicate tool functionality and is subject to variation 
based on product components, temperature and end-
user application.

Self-Discharge 

 

A lithium battery can self discharge and lose its stored 
charge. Typically it can lose approximately 5% of its 
charge in the first month after fully charging (when stored 
at room temperature), and then loses it by a further 3% 
per month. When stored at higher temperatures the self-
discharge rate will be accelerated. 

Transportation

 WARNING: 

Fire hazard. 

Transporting 

batteries can possibly cause fire if the battery terminals 
inadvertently come in contact with conductive materials. 
When transporting batteries, make sure that the battery 
terminals are protected and well insulated from materials 
that could contact them and cause a short circuit.

NOTE: 

Lithium-ion batteries should not be put in 

checked baggage.

Trend batteries comply with all applicable shipping 
regulations as prescribed by industry and legal standards 
which include UN Recommendations on the Transport 
of Dangerous Goods; International Air Transport 
Association (IATA) Dangerous Goods Regulations, 
International Maritime Dangerous Goods (IMDG) 
Regulations, and the European Agreement Concerning 
The International Carriage of Dangerous Goods by 
Road (ADR). Lithium-ion cells and batteries have been 
tested to section 38.3 of the UN Recommendations on 
the Transport of Dangerous Goods Manual of Tests and 
Criteria.

In most instances, shipping a Trend battery pack will 
be excepted from being classified as a fully regulated 
Class 9 Hazardous Material. In general, only shipments 
containing a lithium-ion battery with an energy rating 
greater than 100 Watt Hours (Wh) will require being 
shipped as fully regulated Class 9.

All lithium-ion batteries have the Watt Hour rating 
marked on the pack. Furthermore, due to regulation 
complexities, Trend does not recommend air shipping 
lithium-ion battery packs alone regardless of Watt Hour 
rating. Shipments of tools with batteries (combo kits) can 
be air shipped as excepted if the Watt Hour rating of the 
battery pack is no greater than 100 Whr.

Regardless of whether a shipment is considered 
excepted or fully regulated, it is the shipper’s 

responsibility to consult the latest regulations for 
packaging, labelling/marking and documentation 
requirements.

The information provided in this section of the manual 
is provided in good faith and believed to be accurate 
at the time the document was created. However, no 
warranty, expressed or implied, is given. It is the buyer’s 
responsibility to ensure that its activities comply with the 
applicable regulations.

Storage Recommendations

 

The best storage place is one that is cool and dry 
away from direct sunlight and excess heat or cold. For 
optimum battery performance and life, store battery 
packs at room temperature when not in use.

For long storage, it is recommended to store a fully 
charged battery pack in a cool, dry place out of the 
charger for optimal results.

NOTE: 

Battery packs should not be stored completely 

depleted of charge. The battery pack will need to be 
recharged before use.

Labels on Charger and Battery Pack 

In addition to the pictographs used in this manual, the 
labels on the charger and the battery pack may show the 
following pictographs: -

 

Read instruction manual before use.

 See Technical Data for charging time.

 Battery charging. 

 Battery charged. 

 Battery defective. 

 Delay charge (Battery cooling or too cold 

battery).

 Do not probe with conductive objects.

 Do not charge damaged battery packs. 

 Do not expose to water.

 Have defective cords replaced immediately.

 Charge only between 4ºC and 40ºC. 

 Only for indoor use. 

Summary of Contents for T18S/BJ






































Reviews:

Related manuals for T18S/BJ