Tri-Americas TracVision M7 Installation Manual Download | Manualshive

Page: 8 / 10

background image

9

i.

Using a tie-wrap

(supplied in the kit)

, secure

the RF cables to the LNB to prevent them

from getting snagged when the antenna is in

motion (see Figure 19).

j.

Reattach the radome (see Figure 1 on page 3).

Tie-wrap

RF Cables

Figure 19: Securing RF Cables to the LNB

Continued

Installing the Tri-Americas LNB

«
...
6
7
8
9
10
»

Summary of Contents for TracVision M7











Reviews:

No comments

Related manuals for TracVision M7

Brand: H3C Pages: 7

In-Motion MVT-35B

Brand: Winegard Pages: 8

Brand: MELICONI Pages: 28

Brand: M2 Antenna Systems Pages: 3

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 7

Brand: Philips Pages: 8

Brand: Philips Pages: 8

Brand: Philips Pages: 8

Brand: Philips Pages: 10

Brand: Philips Pages: 12

Brand: Philips Pages: 12

2019 Automatic Tuning Mobile HF Antenna

Brand: Barrett Pages: 8

Brand: Schwaiger Pages: 12

H22dCSS+ Series

Brand: SELFSAT Pages: 72

Brand: Cabletech Pages: 24

Brand: Sirio Antenne Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands