background image

WARNING

!

Indicates a potentially hazardous situation 

which, if ignored, can result in serious  injury or 

substantial property damage.

NOTICE

Indicates special instructions on installation, operation 

or maintenance, which are important to equipment 

but not related to personal injury hazards.

WARNING

!

For your safety, turn off electrical power supply 

at service panel and allow unit to cool before 

proceeding to avoid possible electrical shock and 

scald hazard.  Failure to do so can cause severe 

personal injury or death.

NOTICE

Upon completion of the conversion from Natural Gas to 

Propane, affix the new rating label included in the kit to 

the unit adjacent to the existing rating label.  DO NOT 

affix the new label over the existing rating label. Add 

propane conversion labelling to the gas valve. 

WARNING

!

Failure to follow instructions below can result in 

severe personal injury or damage if ignored.

•  Instructions are for a qualified installer/ 

service technician only.

•  Read all instructions before proceeding.

•  Follow instructions in proper order.

NOTICE

These instructions cover NG to LP conversion for Instinct 

boilers only. Each kit is supplied with one venturi suitable 

for use with that particular boiler model.  

Kit Part Number

•  INSRKIT08 (Solo 110)

•  INSRKIT10 (Solo/Combi 155)

•  INSRKIT12 (Solo/Combi 199)

Kit Includes

•  Rating Label

•  Conversion Label

•  (1) Propane Gas Venturi

•  Acoustic Foam (required for 110 and 155 models ONLY)

Recommended Tools

•  Adjustable Wrench / 10 mm Socket & Ratchet

•  Phillips Head Screwdriver

•  Flat Head Screwdriver

•  Calibrated Combustion Analyzer

Instinct Solo/Combi

Natural Gas to Propane Conversion Instructions

227797 A02

Revision Date: 05/2021

2019-18 Instinct NG to LP  Conversion

NOTICE

When converting the appliance from Natural Gas to Propane ensure that the conversion is completed before fully installing 

the air inlet piping.

Summary of Contents for INSRKIT08







Reviews: