TRIGA TR-FFT Installation & Operation Manual Download

Page: 7 / 33

PRELIMINARY: TR-FFT Fire Fighter’s Telephone Manual — LS10309-001TR-E:A 04/28/2021

Section 1: Overview

The Triga Series TR-FFT Fire Fighter Telephone System provides supervision, annunciation, and control for the local and
remote telephone handsets. The TR-FFT, with keypad, provides indications of phone activation, and corresponding trouble

conditions. Additionally, up to 72 telephone circuits can be annunciated at the TR-FFT by connecting the TR-24Z-EXT zone

expander.

1.1 Features

The TR-FFT features are as follows.
•

One Form-C Trouble Relay, System Trouble Relay - TB6

•

TR-FFT Fire Fighter Telephone module used for control and annunciation of up to 72 remote telephone jacks

•

A maximum of 10 Fire Fighter Remote Handsets (TR-RHS) can be used at one time to communicate over the telephone

circuit connected to the TR-FFT

•

Fire Fighter Phone Jack (TR-FPJ) provides a plug-in location for the TR-RHS

•

Single Telephone Station (TR-STSR/TR-STSS)

•

Fire Fighter Handset Cabinet (TR-HSC) is used to store up to ten Fire Fighter Handsets (TR-RHS)

•

System Status LEDs

•

Supports two TR-24Z-EXT zone expanders

1.2 Optional Accessories

This Manual contains information on how to install the following compatible accessories with the TR-FFT Series equipment:

1.3 Agency Requirements

The TR-FFT has the same requirements as the main control panel. These requirements are listed in the Triga Series Address-

able FACP Installation Manuals. The FACP Installation Manuals can be found on the web site at www.trigaglobal.com.

1.4 About This Manual

This Manual is intended to be a complete reference for all installation and operation tasks for the TR-FFT. For additional infor-

mation, refer to the following FACP Installation Manuals. The documents are located on the Triga website, www.triga-
global.com.

Model Number

Description

TR-24Z-EXT

24 Zone Expander

TR-FPJ

Remote Phone Jack

TR-RHS

Fire Fighter’s Remote Hand Set

TR-HSC

Fire Fighter’s Handset Cabinet

TR-STSR

Single Telephone Station Recessed

TR-STSS

Single Telephone Station Surface Mount

FFT-BGK

Break Glass Kit for TR-STS

TR-MINIMON

Addressable Mini-Monitor Module

TR-ISO

SLC Line Isolation Module

Table 1.1 Optional Accessories

Document

Document Part Number

TR-2100/ECS Manual

LS10143-003TR-E

TR-RPS1 Manual

LS10259-002TR-E

Triga ECS Manual

LS10262-002TR-E

TR-24Z-EXT Product Installation Document

LS10305-001TR-E

TR-FPJ Product Installation Document

LS10306-001TR-E

TR-HSC Product Installation Document

LS10307-001TR-E

TR-STSR/TR-STSS Product Installation Document LS10308-001TR-E

Summary of Contents for TR-FFT


































Search results

Summary of Contents for TR-FFT

Reviews:

Related manuals for TR-FFT

Brands by name

Popular brands

TRIGA TR-FFT, Installation & Operation Manual

Search results

Summary of Contents for TR-FFT

Reviews:

Related manuals for TR-FFT

Brands by name

Popular brands