background image

User's Manual                                                         Rev B / February 2021 / M125 Helium Compressor

 

 

 

97-00020-000    

 

                                                                                                                                           9 

 

 

 
 
 

 

 

 

Figure 3 – Model 125 Dimensions 

4.3

 

Ordering Information 

Table 4-4 contains the ordering information for the Model 125 compressor unit. Customers can also order the optional 

accessories and replacement parts listed in Table 4-5 

 

Table 4-4: Model 125 Compressor Unit Ordering Information 

Compressor Unit 

Part Number 

M125 Water-cooled, Low Voltage, Standard Drive Circuit 

91-00003-0LW 

M125 Air-cooled, Low Voltage, Standard Drive Circuit 

91-00003-1LA 

 

Table 4-5: Optional Accessories and Replacement Parts 

Accessories/Replacement Parts 

Part Number 

Adsorber (Water-cooled model) 

80034 

Adsorber (Air-cooled model) 

80111 

Helium Lines (10ft.*) 

10418-10 

Helium Regulator 

HR-580 

Maintenance Manifold, for helium clean-up process on compressors and 

cryopumps 

10134 

Cryopump Drive Cable (10ft.*), sends power to the cryopump motor from 

the compressor 

10144-10 

Cryopump patch cable (3”), (onboard  10 pin to standard 6 pin) 

81-00053-002 

On-Board drive cable (10ft.*), sends power to the On-Board Cyropump 

motor from the compressor 

81-00005-006 

*Custom length available. 

Summary of Contents for 91-00003-0LW

























Reviews: