For indoor use only. Retain carton for storage purposes.
SAVE THESE INSTRUCTIONS
CAUTION:
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Shaping Instructions
Shaping the tree branches is the last step of
assembly. The care and attention given to this final
process will result in a genuinely beautiful and
appealing holiday centerpiece.
1. Every tree style is shipped from the factory with
the tips of each branch compressed to the center
(Figure 4).
2. Each branch tip must be shaped to it’s proper
position to give the tree a natural look. This is
done by gently grasping the left and right wing tips
and spreading them out away from the center tip
(Figure 5).
3. Each individual tip should then be spread out
separately. Tips should then be bent slightly
upward to add a more natural looking appearance.
Figure 6 shows a typical tree branch after shaping.
4. As you shape closer to the top, the branches will
not have wing tips, but will otherwise shape in the
same manner as lower sections.
Assembly
Each carton contains one top section, one bottom
section and tree stand legs.
1. Slide legs upward into slots at base of bottom
section (Figure 1) and tap lightly with a hammer
until secure. WARNING: Using excessive force to
assemble base may cause breakage.
2. Insert the top tree section into the green plastic
opening of the lower tree assembly. This is the
“pole cap” which keeps tree top section securely in
place (Figure 2).
3. Working your way up from the bottom, gently lower
all branches from their upright setting by grasping
the branch and pulling it downward (Figure 3).
Each branch must be shaped to a natural position
by spreading out the left and right tips away from
the center tip (See Shaping Instructions below).
Continue to lower branches on upper section(s) in
the same manner.
Fig. 1
Fig. 2
Fig. 3
Fig. 6
Fig. 5
Fig. 4
Storage
Remove all holiday decorations. Gently press tips
back into center branch. Raise all branches to
original upright position taking care not to place
undue pressure on the attached ends of the
branches. When disassembling tree, a twisting
motion will help to separate the sections from each
other. All tree parts can be replaced in carton and
should be stored in a cool, dry place.
• Do not use seasonal products
outdoors unless marked suitable for
indoor and outdoor use. When products
are used in outdoor applications,
connect the product to a Ground Fault
Circuit Interrupter (GFCI) outlet. If one
is not provided, contact a qualified
electrician for proper installation.
• This seasonal use product is not intended
for permanent installation or use.
• When decorating trees, use
miniature light bulb strings or LED
light strings only. “C” size bulbs are
not recommended.
• Do not mount or place near gas or
electric heaters, fireplaces, candles or
other similar sources of heat.
• Do not secure the wiring of the product
with staples or nails, or place on sharp
hooks or nails.
• Unplug the product when leaving the
house, when retiring for the night, or if
left unattended.
•
CAUTION:
This is an electrical product
– not a toy! To avoid risk of fire, burns,
personal injury and electric shock, it
should not be played with or placed
where small children can reach it.
• Do not let lamps rest on the supply
cord or any wire.
• Do not use this product for other than
its intended use.
• Do not hang ornaments or other
objects from cord, wire or light string.
• Do not close doors or windows on the
product or extension cords as this may
damage the wire insulation.
• Never operate this product if the power
cord or plug is damaged.
• Use only manufacturer specified
replacement bulbs.
• Read and follow all instructions that
are on the product or provided with the
product.
USE AND CARE INSTRUCTIONS
• When storing the product, carefully
remove the product from wherever it is
placed, including trees, branches, or
bushes, to avoid any undue strain or
stress on the product conductors,
connections, and wires.
• When not in use, store neatly in a
cool, dry location protected from
sunlight.
