background image

Page  12 of 14

                  Part Number 8519184-0000  Rev: B

Certifications, Cautions and Warranty

Certifications:

This enclosure, as a component, has been tested and has passed all safety
requirements. The integrator is responsible for End Product testing and agency
verifications. Do not use the enclosure in any manner other than the intended
use/purpose as advertised by Trimm Technologies. The enclosure meets the
requirements of the following agencies:

 -      -  Underwriters Laboratories, Recognized Component
 –      -  Component conformity with EU Directives
 -      - Canadian Underwriters Laboratories

Testing for other agencies can be done upon request

.

In addition, the enclosure has been designed to meet FCC, Class B emission
requirements. System approval can only be obtained when the enclosure is loaded
with drives. The final step is the integrator’s option, with this task being made easier
due to Trimm’s compliance with agency regulations and attention to anti-emission
construction techniques.

This equipment generates, uses, and may emit radio frequency energy. If not
installed in accordance with the information provided in this manual, it may cause
interference to radio communications. It has been tested and found to comply with
the limits for a Class B computing device pursuant to Subpart J of Part 15 of FCC
Rules, which are designed to provide reasonable protection against such
interference when operated in a commercial environment.

Cautions:

Warnings/Cautions

Watch out for Static while handling/installing drives and/or FRU’s

!

Although  the enclosure is not sensitive to (Static) Electrostatic Discharge (ESD),
any of the electronic circuits, such as the board providing connection from the
external host connection to the internal drives or the drives themselves, are sensitive
to ESD. Heed the warnings and cautions in your drive manual(s). Take care to avoid
damaging your drive and any of the electronic circuit boards by mishandling.
Ideally, a conductive rubber mat and wrist strap should be used if possible,
whenever you are handling any of the drives or electronic circuit boards.

Summary of Contents for UR8J2-4 Series



















Reviews: