Trimteck OPTIMUX OpTK Product Instruction Manual Download

Page: 6 / 8

OpTK Spring Cylinder Rotary Actuators

Figure 1: Sectional View of Actuator with Non-clamping Lever Arm

Note: Item numbers correspond directly to the bill of material; refer to it for specific part numbers.

Cylinder

(Item No. 202)

Spring

(Item No. 229)

Piston Stem O-ring

(Item No. 272)

Piston

(Item No. 225)

Piston Back-up Ring

(Item No. 269)

Piston O-ring

(Item No. 271)

Cylinder O-ring

(Item No. 274)

Spring Button

(Item No. 227)

Actuator Stem Locknut

(Item No. 348)

Actuator Stem O-Ring

(Item No. 275)

Sliding Seal Collar

(Item No. 366)

Base Slider O-Ring

(Item No. 278)

Valve Shaft

(Item No. 51)

Transfer Case

(Item No. 204)

Adjusting Screw

(Item No. 210)

Adjusting Screw Gasket

(Item No. 248)

Cylinder Retaining Ring

(Item No. 256)

Spiral Retaining Ring

(Item No. 368)

Retaining Washer

(Item No. 360)

Actuator Stem

(Item No. 211)

Splined Lever Arm

(Item No. 249)

Yoke/Cover Plate Bearing

(Item No. 258)

Lever Arm Bearing

(Item No. 358)

Pivot Pin

(Item No. 361)

Stroke Stop Jam Nut

(Item No. 347)

Stroke Stop Bolt

(Item No. 330)

Summary of Contents for OPTIMUX OpTK









Search results

Summary of Contents for OPTIMUX OpTK

Reviews:

Related manuals for OPTIMUX OpTK

Brands by name

Popular brands

Trimteck OPTIMUX OpTK, Product Instruction Manual

Search results

Summary of Contents for OPTIMUX OpTK

Reviews:

Related manuals for OPTIMUX OpTK

Brands by name

Popular brands