background image

28

Triple Solar assembly instruction PVT heat pump panels March 2020

11. Maintenance

The heat pump panels are basically maintenance-free. However, there are a few recommendations in this area:

It is recommended to check the connections annually for fluid tightness and corrosion due to external factors 

such as the weather or other conditions.

In the case of vertical installation (90°) against a facade, it is recommended to clean the heat pump panels 

regularly with water if they are not exposed to rain.

Check the fins on the underside of the heat pump panels annually for leaves or insects to maximize the 

performance of the panels.

In case of a system conversion, it is recommended to replace the new glycol resistant O-rings and/or gaskets at 

the disconnected connection hoses.

If the pipes on the roof have to be closed for maintenance, make sure that the expansion tank of the source 

can remain active. After all, the source can heat up and cause the fluid to expand. Close the filter valve 

(supplied with Nibe heat pumps) and the valve of the flush and fill connection set.

12. Warranty conditions

For our terms and conditions, see www.triplesolar.eu. Points of attention here:  

Warranty conditions products

Triple Solar gives a product warranty on the heat pump panels for a period of 10 years.

PV panels, heat pumps and other components are supplied in accordance with the manufacturer's warranty 

(e.g. Bisol guarantees a 10-year product warranty and a 25-year performance guarantee of >85% of the 

initial capacity).

Product warranty is excluded at:

1.

Damage caused by improper assembly, maintenance or repairs in which non-original parts have been 

used.

2.

Defects caused by improper use or use of products other than those for which they were manufactured 

and intended.

3.

Damage caused by external causes.

4.

Discolouration due to UV radiation and lacquer corrosion.

5.

A removed or illegible type plate.

Entrance control:  

Please check the delivered products for any damage immediately upon delivery. In the case of obvious 

defects or incorrect deliveries, this must be reported to Triple Solar in writing by e-mail to 

order@triplesolar.eu at the latest 2 working days after receipt of the products. Please state your order 

number.

No rights can be derived from the information and instructions in these assembly instructions.

Triple Solar BV

Programmeurstraat 6-B 

1033 MT Amsterdam

Tel +31 (0)20 435 7555

info@triplesolar.eu

www.triplesolar.eu

Summary of Contents for M2 300 165 landscape






























Reviews: