8
Specifications
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
SmartPro
®
USB UPS Systems
Model:
SMART500USB
SMART550USB
SMART700USB
Series:
163620U1
AGSM500USBKJR6
AGOM1000USBKSR6
Input Voltage/Frequency:
120V/60 Hz
120V/60 Hz
120V/60 Hz
On-Line Input Voltage Range:
83 - 147 volts
83 - 147 volts
83 - 147 volts
Output Capacity (VA/Watts):
500/300
550/300
700/450
Battery Runtime (Half Load/Full Load) Minutes:
17/5
17/5
20/6
Battery Recharge Time:
2-4 hrs.
2-4 hrs.
2-4 hrs.
Approvals:
UL, cUL, NOM, FCC-B
UL, cUL, NOM, FCC-B
UL, cUL, NOM, FCC-B
Tel/Fax/Data Protection:
1-line tel/DSL
1-line tel/DSL
1-line tel/DSL/Ethernet
OmniSmart
™
UPS Systems
Model:
OMNISMART500
OMNISMART700
OMNISMART850
OMNISMART1000VS
Series:
AGSM500USBKJR6
AGOM700USBKSR61
AGOM1050PJR61
AGOM1000USBKSR6
Input Voltage/Frequency:
120V/60 Hz
120V/60 Hz
120V/60 Hz
120V/60 Hz
On-Line Input Voltage Range:
75 - 147 volts
75 - 147 volts
75 - 147 volts
83 - 147 volts
Output Capacity (VA/Watts):
500/300
700/425
850/600
1000/500
Battery Runtime (Half Load/Full Load) Minutes:
17/5
22/7
26/9
17/5
Battery Recharge Time:
2-4 hrs.
2-4 hrs.
2-4 hrs.
2-4 hrs.
Approvals:
UL, cUL, NOM, FCC-B
UL, cUL, NOM, FCC-B
UL, cUL, NOM, FCC-B
UL, cUL, NOM, FCC-B
Tel/Fax/Data Protection:
1-line tel/DSL
1-line tel/DSL/Ethernet
None
1-line tel/DSL
Model:
OMNISMART1050
OMNISMART1400
Series:
AGOM1050PJR61
AGOM1400PSR61
Input Voltage/Frequency:
120V/60 Hz
120V/60 Hz
On-Line Input Voltage Range:
75 - 147 volts
75 - 147 volts
Output Capacity (VA/Watts):
1050/705
1400/940
Battery Runtime (Half Load/Full Load) Minutes:
23/7
24/8
Battery Recharge Time:
2-4 hrs.
2-4 hrs.
Approvals:
UL, cUL, NOM, FCC-B
UL, cUL, NOM, FCC-B
Tel/Fax/Data Protection:
None
None
ALL UNITS:
Output Waveform Line Mode (filtered sinewave); Output Waveform Battery Mode (PWM sine wave); AC Surge Suppression (exceeds IEEE 587 Cat. A & B standards); AC Noise
Attenuation (>40 dB at 1MHz); AC Protection Modes (H to N, H to G, N to G).
FCC RADIO/TV INTERFERENCE NOTICE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy,
and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to
try to correct the interference using one or more of the following measures: reorient or relocate the receiving antenna; increase the separation between the equipment and receiver; connect
the equipment into an outlet on a circuit different from that which the receiver is connected; consult the dealer or an experienced radio/television technician for help. The user must use shielded
cables and connectors with this product. Any changes or modifications to this product not expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment.
CONSUMER INFORMATION AND FCC REQUIREMENTS (U.S. only):
1. This equipment complies with Part 68 of the FCC rules. On the top or bottom of this equipment is a label that contains, among other information, the FCC registration number for this equipment.
If requested, provide this information to your telephone company.
2. If your Fax/Modem Protector causes harm to the telephone network, the telephone company may temporarily discontinue your service. If possible, they will notify you in advance. But if
advance notice isn't practical, you will be notified as soon as possible. You will be advised of your right to file a complaint with the FCC.
3. Your telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of your equipment. If they do, you will be given advance
notice so as to give you an opportunity to maintain uninterrupted service.
4. If you experience trouble with this Fax/Modem Protector, please contact Tripp Lite Customer Support, 1111 W. 35th Street, Chicago, Illinois 60609; Phone (773) 869-1234 for repair/warranty
information. The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure that the equipment is not malfunctioning.
5. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. (Contact your state public utility commission or
corporation for information.)
EQUIPMENT ATTACHMENT LIMITATIONS (Models with the Industry Canada label in Canada only):
NOTICE: The Industry Canada label identifies certified equipment. This certification
means that the equipment meets the telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical
Requirements Document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed
using an acceptable method of connection. The customer should be aware that the compliance with the above conditions might not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions,
may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together.
This precaution may be particularly important in rural areas. Caution: Users should not attempt to make connections themselves, but should contact the appropriate electric inspection authority,
or electrician, as appropriate.
Note on Labeling
Two symbols are used on the label.
V~ : AC Voltage
V : DC Voltage
200306109 OmniSmart and SmartPro USB Owner’s Manual.qxd 7/14/2003 4:57 PM Page 8
