134
4. Порядок эксплуатации
4.1 Принцип действия кнопок дисплея
Кнопка
Функциональное назначение
Кнопка ON/Enter
("ВКЛ/Ввод")
Включение ИБП:
для включения ИБП нажмите на эту кнопку и удерживайте ее не менее 0,5 с.
Кнопка Enter ("Ввод"):
нажмите на эту кнопку для подтверждения выбранной опции в меню настроек.
Кнопка OFF/ESC
("ВЫКЛ/Отмена")
Выключение ИБП:
для выключения ИБП нажмите на эту кнопку и удерживайте ее не менее 0,5 с.
Кнопка Esc ("Отмена"):
нажмите на эту кнопку для возврата в предыдущий раздел меню настроек.
Кнопка Test/Up
("Тест/Вверх")
Тестирование батареи:
для тестирования батареи в режимах он-лайн и Freq. Converter* (ПРЕОБР. ЧАСТОТЫ) нажмите на эту кнопку и
удерживайте ее не менее 0.5 с .
Кнопка UP ("Вверх"):
нажмите на эту кнопку для отображения следующей опции в меню настроек.
Кнопка Mute/Down
("Отключение звука / Вниз")
Отключение звуковой сигнализации:
для отключения звукового сигнала нажмите на эту кнопку и удерживайте ее не менее 0,5 с.
Подробная информация представлена в
разделе 4.4.9
.
Кнопка Down ("Вниз"):
нажмите на эту кнопку для отображения предыдущей опции в меню настроек.
Кнопки Test/Up + Mute/Down
("Тест/Вверх + Отключение звука / Вниз")
Для входа/выхода в/из меню нажмите на эти кнопки одновременно и удерживайте их не менее 1 секунды. Подробная информация
представлена в
разделе 4.7 Меню Setup (Начальная установка)
* Режим Freq. Converter ("Преобр. частоты") означает постоянное выходное напряжение и постоянную выходную частоту.
4.2 Светодиодные индикаторы и ЖК-панель
Светодиодные индикаторы
ЖК-панель
Светодиодные индикаторы:
На передней панели устройства располагаются 4 светодиодных индикатора, отображающих рабочее состояние ИБП:
Mode / LED (Режим / СИД)
LINE (СЕТЬ)
BYPASS (ОБХ. ЦЕПЬ)
BATTERY (БАТАРЕЯ)
FAULT (ОТКАЗ)
Initialization (Инициализация)
•
•
•
•
Режим ожидания
o
o
o
o
Режим работы по обходной цепи
o
•
o
o
Режим он-лайн
•
o
o
o
Режим питания от батарей
o
o
•
o
Режим Freq. Converter
(Преобр. частоты)
•
o
o
o
Тестирование батарей
•
•
•
o
Режим ECO (экономичный)
•
•
o
o
Отказ
o
o
o
•
Примечание.
•
означает горящий СИД, а o означает выключенный СИД.
LINE
BYPASS
BATTERY
FAULT
(СЕТЬ)
(ОБХ. ЦЕПЬ)
(БАТАРЕЯ)
(ОТКАЗ)
Summary of Contents for S3M30KX
