143
4. Порядок эксплуатации
06: Диапазон напряжений для режима ECO (экономичный)
Интерфейс
Настройка
Параметр 2:
Минимальный уровень напряжения в режиме ECO. Диапазон настройки: от -5% до -10% от номинального
напряжения.
Параметр 3:
Максимальный уровень напряжения в режиме ECO. Диапазон настройки: от +5% до +10% от номинального
напряжения.
07: Диапазон частот для режима ECO (экономичный)
Интерфейс
Настройка
Параметр 2:
Установить минимальный уровень частоты для режима ECO.
50 Hz system: Диапазон настройки составляет от 46,0 до 48,0 Гц.
60 Hz system: Диапазон настройки составляет от 56,0 до 58,0 Гц.
По умолчанию установлено значение 48,0 Гц / 58,0 Гц.
Параметр 3:
Установить максимальный уровень частоты для режима ECO.
50 Hz: Диапазон настройки составляет от 52,0 до 54,0 Гц.
60 Hz: Диапазон настройки составляет от 62,0 до 64,0 Гц.
По умолчанию установлено значение 52,0 Гц / 62,0 Гц.
08: Настройка режима работы по обходной цепи
Интерфейс
Настройка
Параметр 2:
OPN:
Работа по обходной цепи разрешена. При выборе данной опции ИБП будет функционировать в режиме работы по обходной
цепи в зависимости от того, включена или отключена функция перехода на обходную цепь.
FBD:
Работа по обходной цепи запрещена. При выборе данной опции переход в режим работы по обходной цепи запрещен при
любой ситуации.
Параметр 3:
ENA:
Работа по обходной цепи разрешена. При выборе данной опции активируется режим работы по обходной цепи (по
умолчанию).
DIS:
Функция перехода на обходную цепь отключена. При выборе данной опции допускается автоматический переход на
обходную цепь, тогда как ручной переход на обходную цепь запрещен. Ручной переход на обходную цепь означает, что
пользователи вручную переводят ИБП в режим работы по обходной цепи. Например, путем нажатия кнопки OFF (ВЫКЛ) в
режиме переменного тока для включения режима работы по обходной цепи.
09: Установка максимальной длительности разрядки батарей
Интерфейс
Настройка
Параметр 3:
000~999:
Установить максимальное время разрядки в диапазоне от 0 до 999 мин. В случае истечения установленного времени
разрядки до момента падения напряжения батареи до минимального уровня происходит отключение ИБП в целях защиты
батарей от преждевременного выхода из строя. По умолчанию установлено значение 990 мин.
DIS:
Отключить защиту батарей от разрядки; в этом случае время автономной работы будет зависеть от емкости батарей.
10: Зарезервировано
Интерфейс
Настройка
Зарезервировать для дополнительных функций в будущем.
Summary of Contents for S3M30KX
