144
4. Порядок эксплуатации
11: Настройка функции "горячего" резерва
Интерфейс
Настройка
Параметр 2:
HS.H:
Указывает на функцию "горячего" резерва.
Параметр 3:
Включить или отключить функцию "горячего" резерва.
YES:
Функция "горячего" резерва включена. Текущий ИБП устанавливается в качестве хоста для функции "горячего" резерва и
перезапускается после восстановления переменного тока даже без подключенных батарей.
NO:
Функция "горячего" резерва отключена. ИБП функционирует в нормальном режиме и не может перезапускаться при
отсутствии батарей.
12: Обнаружение потери нейтрали
Интерфейс
Настройка
Параметр 2:
N.L:
Указывает на то, что функция обнаружения потери нейтрали включена.
Параметр 3:
DIS:
Отключить функцию обнаружения потери нейтрали. При выборе данной опции ИБП не будет обнаруживать потерю
нейтрали.
ATO:
ИБП будет автоматически обнаруживать, не потеряна ли нейтраль. В случае обнаружения потери нейтрали издается
звуковой сигнал. При включении ИБП он переходит в режим питания от батарей. После восстановления нейтрали и ее
обнаружения звуковой сигнал автоматически отключается, а ИБП автоматически возвращается в нормальный режим.
CHE:
ИБП будет автоматически обнаруживать потерю нейтрали. В случае обнаружения потери нейтрали издается звуковой
сигнал. При включении ИБП он переходит в режим питания от батарей. После восстановления нейтрали звуковой сигнал НЕ
отключается автоматически, а ИБП НЕ возвращается автоматически в нормальный режим.
В этом случае необходимо отключить сигнал и вручную вернуть ИБП в нормальный режим. Порядок действий: сначала войдите
в это меню и нажмите на клавишу “Enter” ("Ввод"), чтобы замигал значок “CHE” ("ПРОВЕРКА"). Затем снова нажмите на клавишу
“Enter” ("Ввод") для включения функции обнаружения нейтрали (проверки). При обнаружении нейтрали звуковой сигнал
отключается, а ИБП возвращается в нормальный режим. Если нейтраль не обнаруживается, то ИБП продолжает подавать
звуковой сигнал до обнаружения нейтрали при выполнении следующей операции ручной проверки.
Опция CHE установлена по умолчанию.
13: Калибровка напряжения батарей
Интерфейс
Настройка
Параметр 2:
Выбрать функцию "
Add
" (Прибавить) или "
Sub
" (Убавить) для корректировки напряжения батареи.
Параметр 3:
Диапазон напряжений составляет от 0 до 9,9 В при значении по умолчанию 0 В.
14: Регулировка напряжения зарядного устройства
Интерфейс
Настройка
Параметр 2:
Выбрать функцию "
Add
" (Прибавить) или "
Sub
" (Убавить) для корректировки напряжения зарядного устройства.
Параметр 3:
Диапазон напряжений составляет от 0 до 9,9 В при значении по умолчанию 0 В.
Примечания.
*Перед осуществлением корректировок напряжения, сначала обязательно отключите все батареи для получения точного значения напряжения
зарядного устройства.
* Любое изменение должно соответствовать техническим требованиям к батарее.
Summary of Contents for S3M30KX
