146
4. Порядок эксплуатации
20: Калибровка напряжения на выходе C
Интерфейс
Настройка
Параметр 2:
Всегда отображает
OP.V
в качестве выходного напряжения.
Параметр 3:
Отображает результат внутреннего измерения напряжения на выходе С. Он может быть откалиброван путем
нажатия кнопки
Up/Вверх
или
Down/Вниз
в соответствии с результатом измерения, полученным с внешнего вольтметра.
Результат калибровки вводится в действие нажатием кнопки
Enter
(Ввод). Калибровочный диапазон ограничивается пределами
+/-9 В. Эта функция обычно используется для систем с параллельным подключением.
*Для представления величины напряжения на выходе С будет отображаться число 2 под надписью
OP.U
.
21: Настройка зарядного тока
Интерфейс
Настройка
Параметр 2:
CHG указывает на функцию корректировки зарядного тока.
Параметр 3:
Устанавливает зарядный ток. Диапазон данной настройки: от 1 до 4 А. Значение по умолчанию: 2 А для моделей
мощностью 30K/40K и 4 А для моделей мощностью 60K/80K.
• 30K-40K: Корректирует зарядный ток только для одной зарядной платы, установленной на ИБП. В случае установки более
одной зарядной платы данная функция не работает.
• 60K-80K: Корректирует зарядный ток только для двух зарядных плат, установленных на ИБП. В случае установки более двух
зарядных плат данная функция не работает.
Примечание.
После увеличения числа зарядных плат все установленные зарядные платы заряжают батарею с максимальной мощностью,
соответствующей току 4 А. Предлагаются два типа комплектов расширения зарядных плат: для ИБП моделей S3M30KX и S3M40KX (комплект типа
CBKIT30-40) и для ИБП моделей S3M60KX и S3M80KX (комплект типа CBKIT30-80).
22: Установка количества зарядных плат
Интерфейс
Настройка
Параметр 2:
CHG указывает на функцию коррекции количества зарядных плат.
Параметр 3:
Устанавливает количество зарядных плат. Диапазон настройки: от 1 до 3. Значение по умолчанию: 1.
• 60K-80K: Две зарядных платы соответствуют одной группе. В случае установки на ИБП четырех зарядных плат данный
параметр должен быть установлен на 2. В случае установки на ИБП шести зарядных плат данный параметр должен быть
установлен на 3.
Примечание.
При увеличении количества зарядных плат данный параметр должен меняться соответственно.
4.8 Описание рабочих режимов/состояний
В приведенной ниже таблице представлена информация, выводимая на ЖК-экран в различных режимах работы и состояниях.
(1) При нормальной работе ИБП на его панели последовательно отображаются семь экранов с представлением 3 входных напряжений по фазам (An, bn, Cn), 3 линейных входных
напряжений (Ab, bC, CA) и частоты, сменяющих друг друга.
(2) При успешной начальной настройке систем ИБП с параллельным подключением отображается один дополнительный экран с надписью “
PAR
” в качестве Параметра 2
и присвоенным номером в качестве Параметра 3, как показано ниже на иллюстрации экрана параметров параллельного подключения. Основному ИБП автоматически
присваивается номер “
001
”. Резервным ИБП присваиваются номера “002” или “003”. В процессе работы возможно динамическое изменение присваиваемых номеров.
Экран параметров параллельного подключения
Summary of Contents for S3M30KX
