background image

Important Safety Instructions

3

Equipment Connection Warnings

•  Use of this equipment in life support applications where failure of this equipment can 

reasonably be expected to cause the failure of the life support equipment or to significantly 
affect its safety or effectiveness is not recommended. 

•  Do not connect surge protectors or extension cords to the output of your UPS. This might 

damage the UPS and may affect the surge protectors and UPS warranties.

•  Connect the UPS to an outlet that is adequately protected against excess currents, short 

circuits and earth faults as part of the building installation.

Battery Warnings

•  Your UPS does not require routine maintenance. Do not open your UPS for any reason. 

There are no user-serviceable parts inside.

•  Batteries can present a risk of electrical shock, chemical hazard and burn from high short-

circuit current. Observe proper precautions. Do not dispose of the batteries in a fire. Do 

not open the  
UPS or batteries. Do not short or bridge the battery terminals with any object. Unplug and 

turn off the UPS before performing battery replacement. Use tools with insulated handles. 

There are no user-serviceable parts inside the UPS. Battery replacement should be 

performed only by authorized service personnel using the same number and type of 

batteries (Sealed Lead-Acid). The batteries are recyclable. Refer to your local codes for 
disposal requirements or visit http://www.tripplite.com/support/recycling-program for 

recycling information. Tripp Lite offers a complete line of UPS System Replacement  

Battery Cartridges (R.B.C.).Visit Tripp Lite on the Web at  

http://www.tripplite.com/products/battery-finder/ to locate the specific 

replacement battery for your UPS.

• When adding an external battery pack, connect only a Tripp Lite recommended battery pack 

of the correct voltage and type. Do not connect or disconnect the external battery pack 

when the UPS is operating on battery power. Visit Tripp Lite on the Web at  

www.tripplite.com/support to locate the specific battery for your UPS.

UPS and Battery Recycling

Please recycle Tripp Lite Products. The batteries used in Tripp Lite products are 

sealed Lead-Acid batteries.  These batteries are highly recyclable. Please refer to 
your local codes for disposal requirements.
You can call Tripp Lite for recycling info at 1.773.869.1234.
You can go to the Tripp Lite Website for up-to-date information on recycling the 

batteries or any Tripp Lite product. Please follow this link:   
http://www.tripplite.com/support/recycling-program/

17-02-143-9336B5.indb   3

3/14/2017   2:03:49 PM

Summary of Contents for SMART1200LCD













Reviews: