background image

14

G

B

H

I

L

O

J

M

P

K

N

6-4 Battery Mode Startup (Cold Start)

6-5 UPS System Shutdown

6-6 UPS System Settings and Measurements

6 – Standard Operation 

continued

The UPS system supports battery mode startup (cold start), allowing it to operate as a standalone power source when AC input power is 
unavailable.

1.  Make sure the UPS system is properly installed and the battery is at least partially charged.

2.  Some electronic equipment may draw more amps during startup; consider reducing the initial load on the UPS system.

3.  Press the ON button   for approximately 5 seconds, then release it. The UPS will beep twice and the LCD screen will change from 

A

 to 

G

.

4.  Press the ON button   again for approximately 3 seconds, then release it. The UPS will beep twice and the LCD screen will change from 

G

 to 

H

. (The UPS system will remain awake for approximately 15 seconds after completing the previous step. If you do not press the ON 

button again before 15 seconds have elapsed, you will need to repeat the previous step.)

5.  The UPS system will run a self-test and display 

H

 again. Battery mode startup is successful and connected equipment will operate until the 

battery is depleted (or until pre-defined shutdown parameters have been reached).

1.  Press the OFF button for approximately 5 seconds, then release it. The inverter output will turn off and the LCD screen will show 

B

.

2.  Turn off the UPS system’s utility input breaker.

3.  The UPS system is now completely off. If the UPS system will be turned off for a significant length of time, follow the battery recharging 

instructions in 

Section 11 – Storage and Service

.

Checking UPS System Measurements

To check the values measured by the UPS, scroll up   or down   through the LCD panel. Scrolling down will display values in the following 

order:

This screen indicates the UPS inverter is off and utility input is abnormal.

This screen indicates the UPS inverter is off.

This screen shows the utility input voltage is zero.

Bypass Input Voltage 

Output Voltage

Battery Voltage 

Utility Input Frequency 

Output Frequency

Inner Temperature (°C)

Bypass Input Frequency

Output Load Percentage 

Summary of Contents for SmartOnline SU10KRT1X






















Reviews: