background image

15

Q1

Z

V3

BB

S2

AA

R1

Q2

V4

U

T

R2

V1

S1

W

X

Y

V2

6-6 UPS System Settings and Measurements 

continued

6 – Standard Operation 

continued

Settings and Special Functions

After the UPS starts up completely, press 

 to view settings and execute special functions. Scroll down   to review the settings. Use the    

button to execute special functions. Special functions include buzzer ON 

Q1

 or buzzer OFF 

Q2

 and self-test OFF 

R1

 or self-test ON 

R2

.

Changing Default Settings

Make sure the UPS system is OFF 

Z

. Press the “ON” button   and “Next” button   simultaneously for approximately three seconds until the 

buzzer sounds twice, then release the buttons. Except for buzzer 

Q1

 / 

Q2

 and self-test 

R1

 / 

R2

, all other default settings may now be changed 

by pressing the “Previous/Change Setting”   button. After changing settings, press the “Enter” button   to save all changes 

AA

. To cancel all 

changes, press and hold the OFF   button for five seconds, then release the button 

BB

.

Buzzer “ON”

Bypass Acceptance Range #2

Fixed 50 Hz Output 

Buzzer “OFF” 

Frequency Tolerance Window

Fixed 60 Hz Output

Self-Test “OFF”

Output Voltage Setting

Output Voltage Adjustment (±3%) 

Self-Test “ON”

UPS Off

UPS Normal Mode

Data Saved 

UPS Identification Number

Settings Changes Canceled

Bypass Acceptance Range #1 

UPS Economy Mode

Parallel Mode Enable/Disable 
(P 02 = Parallel Mode Enable) 

Summary of Contents for SmartOnline SU10KRT1X






















Reviews: