background image

3

Quick Installation

Connect your computer to
the UPS, and the UPS to an
electrical outlet.

Plug your equipment into the
UPS's outlets.

Cords and receptacle adapters are available from
Tripp Lite

 

to accommodate most outlet configura-

tions. If rewiring is necessary, refer to the Wire
Color-Code Chart in "Specifications", pg. 6.

Your UPS is designed to support only computer equipment.
You will overload your UPS if you connect household
appliances, laser printers or surge suppressors to the
battery-supported outlets.

3

2

1

1. Unplug your computer’s power cord from both

your AC outlet and your computer’s AC input.

2. Insert the female plug of your computer’s cord

(B) into your UPS’s AC input. Insert the male
plug of your computer’s cord into your AC
outlet.

3. Find the power cord that came with your UPS

(A). Insert the UPS cord’s female plug into your
computer’s AC input. Insert the UPS cord’s
male plug into any of your UPS’s female output
receptacles.

A

B

Set your UPS’s “OFF – ON” Switch.*

USA, Canada & Western Europe
• Set it and leave it “ON” at all times.

All Other Countries
• Set to “OFF” when you are not using connected equipment.

(WARNING! When set to “OFF,” UPS  will not provide battery
backup during a blackout or  brownout)

• Set to “ON” when you are using connected equipment.

*See Basic Operation section for the Switch Function, UPS Conditions and Setting Advantages.

–Optional Installation–

(Select models)

OPTION 1 (Phone-Line Surge Suppression)

††

Using telephone cords, connect your wall jack to the
UPS jack marked “LINE” (or “IN”).  Connect your
equipment to the UPS jack marked “EQUIP” (or “OUT”).

OPTION 2 (UPS Software)
Using Tripp Lite cable (if supplied), connect the DB9
port of your  computer to the DB9 port of your UPS.
Load software (if supplied) and run installation
program appropriate for your operating system.

†These connections and settings are optional.  Your UPS will
function properly without these connections and settings.
††Make sure the equipment you connect to the UPS’s
telephone jacks is also protected against surges on the AC line.

OPTIONS 1 & 2

(Continued)

SEE MANUAL

200008280 Internet I 230V Owner's Manual.p65

8/25/00, 2:35 PM

3

Summary of Contents for Standby UPS Systems Internet I







Reviews: