background image

Installation

Intelligent Gyro Compass (iGC)

0707-SOM-00004-7

18

© Tritech International Ltd.

Once  the  DIL  switch  has  been  set,  the  RS485  jumpers  should  be  checked  and  set

accordingly.
The Jumpers are identified as the shorting links (see photograph). The position to set the

Jumpers can be seen from the photographs below:

Settings for RS485 Mode

Terminated with 120R

Unterminated

Note

For newer iGC units, JP1 and JP2 are no longer tri-state jumpers.

4.5.  Electrical Installation

The following procedure should be followed to complete the Electrical Installation of the iGC:
1. Make any necessary wiring and modifications to the Host control system to provide the

appropriate power supply and telemetry circuits

2. With the power to the Host control system isolated, attach the interconnecting cable to the

appropriate underwater connector at the Host end

3. Using a digital multimeter, insert probes into sockets 1 and 2 of the interconnecting cable

(prior to connecting to the iGC)

4. Carefully power-up the Host supply (or the iGC supply circuit if switchable). Confirm that

the output voltage is the correct value and polarity

Caution

Do not connect the cable to the iGC until provision of correct voltage to the correct

pins on the iGC connector has been checked (see Section 5 - Commissioning).

Summary of Contents for iGC





















































Reviews: