background image

18 

 

 
…and finally fold the hull again from the bow on the folded side of the stern: 
 

  Done! 

 
 

10)  Care, Safety, Storage and further Information: 

 

 
Salt water:

 

 

 
If you want to use your boat in the brackish water / salt water, 
the treatment of the rod with "CorroFilm" is absolutely 
recommended.

 Ask your local Dealer for it! 

 
CorroFilm can be sprayed onto (and if necessary also in) the rods 
and generates a transparent, dry protective film which protects the 
aluminum perfectly against the "attack" of salt water. Ask your 
dealer about CorroFilm. Clean the rods and boat skin after exposing 
it to salt water (e.g. after the tour) with sufficient fresh water. 
 
 

Important

: If the boat is to be stored for a longer time, take the air 

out of the sponsons! A folding boat should be built up and removed 
several times a year. 
 
Ensure that the boat skin and rods are dry when packed and stored. 
 
The boat skin is resistant to salt water. Nevertheless, it should also 
be cleaned with fresh water after the return from a tour in brackish 
or salt water. Especially when sand or small stones can cause high 
abrasion. 
 
Please make sure to carry the boat not only by the handles, but also support it from the 
bottom, in order to relieve the handles from tension. 
 
Always wear a life jacket when you are using your boat on the 
Waters! Beware of rapid weather changes! 
 
 
 
 
 
 
 
 
 

Summary of Contents for Vuoksa 2 advanced





















Reviews: