background image

4

Thank you for purchasing this Triton tool. This manual contains information necessary for safe and effective operation of this product.  

This product has unique features and, even if you are familiar with similar products, it is necessary to read this manual carefully to ensure 

you fully understand the instructions. Ensure all users of the tool read and fully understand this manual.

Description of Symbols  

Wear hearing protection 
Wear eye protection
Wear breathing protection
Wear head protection

Wear hand protection

Read instruction manual 

Toxic fumes or gases!

Caution!

Always disconnect from the power supply when adjusting, 
changing accessories, cleaning, carrying out maintenance and 
when not in use!

Be aware of kickback!

Important safety devices! Ensure correct function, maintain in 
accordance with instructions and DO NOT disable!

Class II construction (for battery charger only) 

For indoors use only (battery charger and PSU)!

DO NOT incinerate batteries!

Internal time-lag fuse with rated current 3.15A

Environmental Protection 
Waste electrical products and batteries, including Li-Ion batteries, 
should not be disposed of with household waste. Please recycle 
where facilities exist. Check with your local authority or retailer 
for recycling advice.

Conforms to relevant legislation and safety standards. <Choose 
correct symbol for region>

V

Volts

~, a.c.

Alternating current

A, mA

Ampere, milli-Amp

n

0

No load speed

n

Rated speed

Ø

Diameter

°

Degrees

λ

Wavelength

Hz

Hertz

     , d.c.

Direct current

W, kW

Watt, kilowatt

/min or min

-1

(revolutions or reciprocation) per minute

Ah

Amp hours (battery capacity)

dB (A)

Decibel sound level (A weighted)

m/s

2

Metres per second squared (vibration magnitude)

Technical Abbreviations Key

T-130°

814386_Z1MANPRO1.indd   4

06/08/2015   09:59

Summary of Contents for XT18













Reviews: