Models: 02-1040C0111 & 02A1040C0111
10 Ton (8.93 Metric Ton) Single Stage Jack
12/2020 | Rev. 02
Page | 4
6.0
OPERATION
6.1
OPERATING PARAMETERS
1. The user shall work in accordance with the Operator Manual.
2. At no time shall personnel work under the raised load until it is secured by suitable means, i.e. ram locknut.
3. The employer of the operator shall provide for all necessary training and give information about pumping and translating
forces.
4. Operate between -20
C and 50
C (-4
F and 122
F).
6.2
NUMERICAL VALUES
•
Rated Capacity ......................... 20,000 lbs (9,073 kg)
•
Minimum Closed Height ........... 40 in (101.6 cm)
•
Mechanical Extension .............. 14 in (35.56 cm)
•
Hydraulic Extension ................. 24 ¼ in (61.6 cm)
•
Maximum Height Obtainable .... 78 ¼ in (198.75 cm)
•
Weight ...................................... 207 lbs (93.9 kg)
•
Pressure Relief Setting ............ 2500 + 250/-0 psig (207+21/-0 bar)
•
Noise level is 64 dB(A) at a distance of 120 in (304.8 cm) at an inlet pressure of 100 psi (6.9 bar)
6.3
OPERATOR CONTROLS
See illustration
6.4
OPERATING INSTRUCTIONS
The user should be familiar with the following statements prior
to using the jack(s):
CAUTION!
1. NEVER put hands between the aircraft and
the jack pad; as after aircraft has been
lowered, struts may have hung up.
2. NEVER align jack under aircraft by pounding
on jack legs. Dented legs may lead to jack
collapse.
3. ALWAYS lower ram locking nut(s) after jack
is under load. Be sure ram nut(s) is seated
fully after jacking.
4. ALWAYS raise and lower jacks
simultaneously so that aircraft remains level.
5. ALWAYS use a tail or nose stand, as
applicable, for additional stability.
6.4.1
Rules For Operating:
1. The user shall work in accordance with the Operator and/or
Technical Manuals.
2. At no time shall personnel work under the raised load until it
is secured by suitable means, i.e. ram locknut.
3. The employer of the operator shall provide for all necessary
training and give information about pumping and translating
forces.
4. Operate between -20
C and 50
C/-4
F and 122
F.
Summary of Contents for 02-1040C0111
